Post your FULL mod list.
- Thread starter Aeroking
- Start date
warmpancakes
New member
Re: Post your FULL mod list.
exterior paint, wheels
interior only stock piece is the cluster
exterior paint, wheels
interior only stock piece is the cluster
Aeroking
e.i.
Re: Post your FULL mod list.
no real intent, just curiousity
Exterior
- 2" Goodmark cowl hood
- 3" 'cuda style stainless exhaust tip
- grille top filler panel
- clear corners & parking lenses
Interior
- 3 pod pillar
- gauges Boost / AFR / Trans Temp
- Pioneer head unit
- Code$59 tuned by owner
- PLX wideband
Eng. Drive.
- Stock Block bored .030 over, 4bolt splayed
- TRW pistons on Eagle h-beam rods
- Total Seal rings and Clevite bearings
- Melling hi-volume oil pump (the good one)
- Double roller chain
- Turbotime custom grind 218 cam
- Waller L35 heads, ported, 2.02/1.60
- Comp 1.6 rockers (.570 lift), pushrods, beehive springs
- stock intake, plenum & throttle body
- stock W2A, soft lines, added coolers, Johnson pump
- PTE-72GTQ, stock exhaust manifolds
- Homemade 3" stainless downpipe, Tial 38mm wastegate, Magnaflow muffler
- K&N cone, 4" Cobra Elbow
- Razor's Alkycontrol on 100% meth
- 3bar Map, EGR delete
- RPM brake booster hose
- A/C system removed
- MSD cap/rotor, MSD 6AL, Taylor 8.2 wires, UR5 plugs
- 12v Solenoid boost controller from ECM
- torque turnbuckle
- Powermaster 140A
- Optima redtop in bed
- Siemens 65# injectors, billet AFPR
- Homemade twin in-tank Walbro 255 hi-press pumps
- Racetronix harness
- Flexa-lite alum. radiator
- Flexa-lite electric rad fan
- Derale trans cooler with fan
- HD propshaft
- Rossler Terminator 2 700R4 with billet upgrades, 65E pan
- 3400 lockup converter
- Blake HD shifter cable
- Blake adjustable TV cable
- M.Campbell custom engraved diff cover
Suspension
- Nitro drop shocks
- Belltech drop leaf springs, pinion wedges & setback plates
- Homemade front end limiters
- ZQ8 steering box, Jeep shaft
- LS1 disc brakes, proportion valve
- ABS complete delete
- 1989 Corvette 17"x9.5" wheels
no real intent, just curiousity
Exterior
- 2" Goodmark cowl hood
- 3" 'cuda style stainless exhaust tip
- grille top filler panel
- clear corners & parking lenses
Interior
- 3 pod pillar
- gauges Boost / AFR / Trans Temp
- Pioneer head unit
- Code$59 tuned by owner
- PLX wideband
Eng. Drive.
- Stock Block bored .030 over, 4bolt splayed
- TRW pistons on Eagle h-beam rods
- Total Seal rings and Clevite bearings
- Melling hi-volume oil pump (the good one)
- Double roller chain
- Turbotime custom grind 218 cam
- Waller L35 heads, ported, 2.02/1.60
- Comp 1.6 rockers (.570 lift), pushrods, beehive springs
- stock intake, plenum & throttle body
- stock W2A, soft lines, added coolers, Johnson pump
- PTE-72GTQ, stock exhaust manifolds
- Homemade 3" stainless downpipe, Tial 38mm wastegate, Magnaflow muffler
- K&N cone, 4" Cobra Elbow
- Razor's Alkycontrol on 100% meth
- 3bar Map, EGR delete
- RPM brake booster hose
- A/C system removed
- MSD cap/rotor, MSD 6AL, Taylor 8.2 wires, UR5 plugs
- 12v Solenoid boost controller from ECM
- torque turnbuckle
- Powermaster 140A
- Optima redtop in bed
- Siemens 65# injectors, billet AFPR
- Homemade twin in-tank Walbro 255 hi-press pumps
- Racetronix harness
- Flexa-lite alum. radiator
- Flexa-lite electric rad fan
- Derale trans cooler with fan
- HD propshaft
- Rossler Terminator 2 700R4 with billet upgrades, 65E pan
- 3400 lockup converter
- Blake HD shifter cable
- Blake adjustable TV cable
- M.Campbell custom engraved diff cover
Suspension
- Nitro drop shocks
- Belltech drop leaf springs, pinion wedges & setback plates
- Homemade front end limiters
- ZQ8 steering box, Jeep shaft
- LS1 disc brakes, proportion valve
- ABS complete delete
- 1989 Corvette 17"x9.5" wheels
Last edited:
epix
Typhoon
Re: Post your FULL mod list.
Probably missing a few things but:
-=Engine=-
4.3L V6 bored 30 over
SRP Forged Pistons
Eagle H-Beam Forged Rods
GM L35 Heads built up
65lb Injectors (700cc)
PTE 63e Turbocharger
TiaL style wastegate
RJC Manual Boost Controller
Custom FMIC with 3.0" piping
Alcohol Injection Kit
Stock ECM wideband tuned/ostrich emulation
Kenne Bell AFPR
Walbro 255lph fuel pump
-=Transmission=-
700R4 Rebuilt with beefier components
3000 RPM Stall Convertor
B&M Transmission Cooler mounted in stock lower IC bracket
Safety Loops for Propshaft and Driveshaft
-=Suspension=-
KYB Monomax Shocks
RPM Rear Sway Bar
Rancho RS9000 Steering Stabilizer
2" Drop Blocks
ABS Delete
-=Appearance=-
HoK Tangerine Candy of Aztec Gold
PPG Midnight Black
17" Boyd Wheels (17x11 rears, 17x9.5 fronts)
BFG Comp T/A Tires (315 rear/275 front)
Lowered 2"
2" Goodmark Steel Hood
Custom Typhoon Decals
Antenna Shaved
New Carpet
PLX Wideband Gauge
NiteGlo Boost Gauge and Temp Gauge
Diamond Euro Headlights
Tinted Tail Lights
-=Audio=-
2x 15" Adire Tempest Subwoofers in custom 8.0CU ported box
JBL 1200.1 Amplifier
CDT Components in custom kickpanels
Infinity Kappa 6x9 rears
Pioneer 4x6 fronts
Lightning Audio S4.600 amplifier for speakers
KnuKoncepts Wiring Kit
Deading Material
Optima Red Top Battery
160Amp Alternator
Probably missing a few things but:
-=Engine=-
4.3L V6 bored 30 over
SRP Forged Pistons
Eagle H-Beam Forged Rods
GM L35 Heads built up
65lb Injectors (700cc)
PTE 63e Turbocharger
TiaL style wastegate
RJC Manual Boost Controller
Custom FMIC with 3.0" piping
Alcohol Injection Kit
Stock ECM wideband tuned/ostrich emulation
Kenne Bell AFPR
Walbro 255lph fuel pump
-=Transmission=-
700R4 Rebuilt with beefier components
3000 RPM Stall Convertor
B&M Transmission Cooler mounted in stock lower IC bracket
Safety Loops for Propshaft and Driveshaft
-=Suspension=-
KYB Monomax Shocks
RPM Rear Sway Bar
Rancho RS9000 Steering Stabilizer
2" Drop Blocks
ABS Delete
-=Appearance=-
HoK Tangerine Candy of Aztec Gold
PPG Midnight Black
17" Boyd Wheels (17x11 rears, 17x9.5 fronts)
BFG Comp T/A Tires (315 rear/275 front)
Lowered 2"
2" Goodmark Steel Hood
Custom Typhoon Decals
Antenna Shaved
New Carpet
PLX Wideband Gauge
NiteGlo Boost Gauge and Temp Gauge
Diamond Euro Headlights
Tinted Tail Lights
-=Audio=-
2x 15" Adire Tempest Subwoofers in custom 8.0CU ported box
JBL 1200.1 Amplifier
CDT Components in custom kickpanels
Infinity Kappa 6x9 rears
Pioneer 4x6 fronts
Lightning Audio S4.600 amplifier for speakers
KnuKoncepts Wiring Kit
Deading Material
Optima Red Top Battery
160Amp Alternator
warmpancakes
New member
Re: Post your FULL mod list.
exterior all new sheetmetal custom paint, (cant disclose color) some other mods hidden 3rd brake lamp
interior, custom seats changed interior color to Tan, seats are tan leather with perforated insersm wilton wool carpet, real suede headliner, some other "things" roll down back window
engine bowtie stroker motor, t-88, sheetmetal intake, 6l60e trans (if I can finish it) drive by wire so I can eliminate all the cables.
wheels Im not sure I have some 18s but they were for sale no the wife wants them for her truck
brakes 13inch front 3 piston calipers rear same as front
exterior all new sheetmetal custom paint, (cant disclose color) some other mods hidden 3rd brake lamp
interior, custom seats changed interior color to Tan, seats are tan leather with perforated insersm wilton wool carpet, real suede headliner, some other "things" roll down back window
engine bowtie stroker motor, t-88, sheetmetal intake, 6l60e trans (if I can finish it) drive by wire so I can eliminate all the cables.
wheels Im not sure I have some 18s but they were for sale no the wife wants them for her truck
brakes 13inch front 3 piston calipers rear same as front
Syclone#1992
SyTy.net Moderator
Re: Post your FULL mod list.
Exterior:
Goodmark Steel Cowl Hood
Smaller Mirrors
Blade of Death, and IC Scoop
Interior:
3 gauge pillar pod. (Boost, IC Temp, and Fuel Pressure)
Engine/Drivetrain:
Hood Chip
ATR Cold Air with K&N
Manual Boost Controller
Walbro Fuel Pump
ATR Adjustable FP Regulator
Taylor wires and Conrad Cap and Rotor
Chrome 180AMP altenator
Battery Shut Off
ATR Battery Relocation
Phil Chivers Propshaft Safety Loop
IC Scoop
Chrome Trans Pan
Powdercoated inner fenders
EGR Block off by Mike Campbell
Chrome rear end cover
ATR exhaust with Chrome Tip
Wheels/Suspension:
Chrome ZR-1 Rims with Sumitumo Tires (315's in the rear)
Painted Calipers and Drums
Rear sway bar to be installed.
Stereo:
Pioneer Speakers and Head Unit
Think thats it!
Exterior:
Goodmark Steel Cowl Hood
Smaller Mirrors
Blade of Death, and IC Scoop
Interior:
3 gauge pillar pod. (Boost, IC Temp, and Fuel Pressure)
Engine/Drivetrain:
Hood Chip
ATR Cold Air with K&N
Manual Boost Controller
Walbro Fuel Pump
ATR Adjustable FP Regulator
Taylor wires and Conrad Cap and Rotor
Chrome 180AMP altenator
Battery Shut Off
ATR Battery Relocation
Phil Chivers Propshaft Safety Loop
IC Scoop
Chrome Trans Pan
Powdercoated inner fenders
EGR Block off by Mike Campbell
Chrome rear end cover
ATR exhaust with Chrome Tip
Wheels/Suspension:
Chrome ZR-1 Rims with Sumitumo Tires (315's in the rear)
Painted Calipers and Drums
Rear sway bar to be installed.
Stereo:
Pioneer Speakers and Head Unit
Think thats it!
dgoodhue
BuSTeD 4.3
Re: Post your FULL mod list.
Exterior
Black GMC Letters
Bed Rug
Skelton Radiator Support
Fiberglass front & rear bumper supports
Interior
Embroidered Floor Mats
3 Pillar Pod w/Boost, Fuel and Tranny Temps
Switch & Knobs for Electrical Fans, MSD 2 step, Alky, and Gain
PLX WB02 and Ultimate Display
Engine/Drivetrain
K&N Air FIlter
PTE 61BB Turbo
A2A IC
Vortec Long Block (very soon)
L35 Cam
Port Match Intake & Modified Lower Intake for Vortecs
Turbotime 3" Down Pipe and High Flow Cat
Borla Exhaust
Alkycontrol
MSD 6AL Ignition & 2 step
Flexalite Electric Fans
Walbro FP
AFPR
50# Injectors
Code $59 (soon)
JS engine pads mounts & poly motor mounts
Hartman Stage 4 Transmission (soon)
TCS 9/11 2800 RPm stall TC
Gilbert Propshaft
Wheels/Suspension
Stock Wheels and Tires size
Front-
16" Baer Brakes
JS Coilovers Front Suspension
Dunstan Tie Rods
ZQ8 Steering Box
Renz's Shaft
Rear
7/8 Wheel Cylinders
Aluminum Drums
Belltech Lowering Spring
Belltech Sway Bar (soon)
QA1 rear coilover shocks
Stereo
Kenwood PS909 CD Player
Boston Acoustics Z6 Components in front doors
Exile Xtec 10" Sub
Phoenix Gold TI500.4AL Amplifier (Imported Aluminum Version)
All enclosures were done in Birch Plywood and Fiberglass to reduce weight. Door were lightly sound deadend (again watching weight gain)
Exterior
Black GMC Letters
Bed Rug
Skelton Radiator Support
Fiberglass front & rear bumper supports
Interior
Embroidered Floor Mats
3 Pillar Pod w/Boost, Fuel and Tranny Temps
Switch & Knobs for Electrical Fans, MSD 2 step, Alky, and Gain
PLX WB02 and Ultimate Display
Engine/Drivetrain
K&N Air FIlter
PTE 61BB Turbo
A2A IC
Vortec Long Block (very soon)
L35 Cam
Port Match Intake & Modified Lower Intake for Vortecs
Turbotime 3" Down Pipe and High Flow Cat
Borla Exhaust
Alkycontrol
MSD 6AL Ignition & 2 step
Flexalite Electric Fans
Walbro FP
AFPR
50# Injectors
Code $59 (soon)
JS engine pads mounts & poly motor mounts
Hartman Stage 4 Transmission (soon)
TCS 9/11 2800 RPm stall TC
Gilbert Propshaft
Wheels/Suspension
Stock Wheels and Tires size
Front-
16" Baer Brakes
JS Coilovers Front Suspension
Dunstan Tie Rods
ZQ8 Steering Box
Renz's Shaft
Rear
7/8 Wheel Cylinders
Aluminum Drums
Belltech Lowering Spring
Belltech Sway Bar (soon)
QA1 rear coilover shocks
Stereo
Kenwood PS909 CD Player
Boston Acoustics Z6 Components in front doors
Exile Xtec 10" Sub
Phoenix Gold TI500.4AL Amplifier (Imported Aluminum Version)
All enclosures were done in Birch Plywood and Fiberglass to reduce weight. Door were lightly sound deadend (again watching weight gain)
Last edited:
TYPHOOL7
Post Hawk
Re: Post your FULL mod list.
Exterior- Stock
Removed:
Ac, Heat, ABS, Fenders, everything that isnt needed to shave weight (full interior)
Undercarrige:
RPM tubular coil overs white w red springs qa1
Flex a Form cf leafs
8.5 in rear axle
Beefy propshaft
Trans:
700r4 built to the teeth by RPM
3000 stall TCS
Engine:
t66dbb innovative turbo
TiAL Sport 46mm Wastegate
TiAL Sport Blow Off Valve
KB headers w jet hot hyper 2000
RPM 3' dp coated
Pontiac aluminum heads w RPM Aluminum Valve Covers
JE Extreme Duty Pistons
Eagle H beams Rods
Nitrided crank
Mezier electric water pump
Aluminum radiator
Spearco IC
Aluminum piping
Wilson intake manifold
90mm TB
Innovative MSBC2
F.A.S.T ecu
84lb injs
RPM Billet fuel rail
Bosch High per inline fuel pump
MSD digital 7 (soon) currently 6al
GOD MUCH MUCH MORE...........................
Exterior- Stock
Removed:
Ac, Heat, ABS, Fenders, everything that isnt needed to shave weight (full interior)
Undercarrige:
RPM tubular coil overs white w red springs qa1
Flex a Form cf leafs
8.5 in rear axle
Beefy propshaft
Trans:
700r4 built to the teeth by RPM
3000 stall TCS
Engine:
t66dbb innovative turbo
TiAL Sport 46mm Wastegate
TiAL Sport Blow Off Valve
KB headers w jet hot hyper 2000
RPM 3' dp coated
Pontiac aluminum heads w RPM Aluminum Valve Covers
JE Extreme Duty Pistons
Eagle H beams Rods
Nitrided crank
Mezier electric water pump
Aluminum radiator
Spearco IC
Aluminum piping
Wilson intake manifold
90mm TB
Innovative MSBC2
F.A.S.T ecu
84lb injs
RPM Billet fuel rail
Bosch High per inline fuel pump
MSD digital 7 (soon) currently 6al
GOD MUCH MUCH MORE...........................
Last edited:
sytyguy
Moderated User
Re: Post your FULL mod list.
Interior - dual pod w/ boost & trans temp, wideband, Grant SW,
Exterior - side mirrors, clear lenses, black grille letters, refinished stock wheels with Ecsta 711s, getting repainted, Extang cover
Engine/Powertrain - 50#ers, 412 cam, TRWs, L35s, 60-1 turbo, RPM DP, Waller trans, 2800 stall 9/11, Waller Upper IC, HTP chip, electric fans, relocated battery, relocated trans cooler, deep trans pan, Johnson IC Pump, custom IC scoop, custom CAI, solid mounts, walbro 255, 3/8" fuel lines, AFPR
Brakes/Suspension/Etc... - coilovers, ABS delete, removal of lots of weight,
Hood
Interior - dual pod w/ boost & trans temp, wideband, Grant SW,
Exterior - side mirrors, clear lenses, black grille letters, refinished stock wheels with Ecsta 711s, getting repainted, Extang cover
Engine/Powertrain - 50#ers, 412 cam, TRWs, L35s, 60-1 turbo, RPM DP, Waller trans, 2800 stall 9/11, Waller Upper IC, HTP chip, electric fans, relocated battery, relocated trans cooler, deep trans pan, Johnson IC Pump, custom IC scoop, custom CAI, solid mounts, walbro 255, 3/8" fuel lines, AFPR
Brakes/Suspension/Etc... - coilovers, ABS delete, removal of lots of weight,
Hood
allwheeldriven
New member
Re: Post your FULL mod list.
Exterior:
Checkpro tonneau cover
Interior:
Autometer tach and boost gauge
Engine/Drivetrain:
Slowmaster exhaust
Cone air filter
TA-Performance Rear diff cover
B&M cast aluminum deep transmission pan
Red Line fluids
Wheels/Suspension:
Z07 18 x9.5+53 wheels with 265/35 Bridgestone RE-01 R tires
Stoptech C5 ST-40 front calipers with 355mm 2 piece rotors
Corvette Z51 rear disc brake conversion
Energy Suspension bushings and bump stops
RPM front coilover
RPM rear coilover with double adjustable shocks
Belltech front and rear sway bars
Belltech lowering leafs
ZQ8 steering box
Upgraded steering shaft
Moog tie rods /ball joints
edelbrock tie rod sleeve
Stereo:
Exterior:
Checkpro tonneau cover
Interior:
Autometer tach and boost gauge
Engine/Drivetrain:
Slowmaster exhaust
Cone air filter
TA-Performance Rear diff cover
B&M cast aluminum deep transmission pan
Red Line fluids
Wheels/Suspension:
Z07 18 x9.5+53 wheels with 265/35 Bridgestone RE-01 R tires
Stoptech C5 ST-40 front calipers with 355mm 2 piece rotors
Corvette Z51 rear disc brake conversion
Energy Suspension bushings and bump stops
RPM front coilover
RPM rear coilover with double adjustable shocks
Belltech front and rear sway bars
Belltech lowering leafs
ZQ8 steering box
Upgraded steering shaft
Moog tie rods /ball joints
edelbrock tie rod sleeve
Stereo:
Last edited:
Jimmy
Banned
Re: Post your FULL mod list.
Exterior:
BC/CC paint
chrome 1/2 headlight covers
no badges.
Interior:
3 gauge pillar pod
tinted windows
boost controller
ecm in the glovebox.
battery in the back
Engine/drivetrain:
Stock motor bored .030
forged pistons
Atr cam
port and polished LB4 heads
Port matched upper/lower intakes
#50 injectors
3 bar MAP
AFPR
Walbro 255
PT-54 turbo
custom cold air intake
Atr DP
EGR/cat/muffler delete
ATR Auxillary IC
Shurflo pump
3/4 rubber IC lines
Razor's alky kit
LM-1 wideband running through the stock ECM
Gilbert propshaft
Waller built 700r
2800 9/11
motorhome tranny cooler
TCI deep trans pan
gear reduction starter
purple wire replaced with 10 gauge from the brake booster down
Exterior:
BC/CC paint
chrome 1/2 headlight covers
no badges.
Interior:
3 gauge pillar pod
tinted windows
boost controller
ecm in the glovebox.
battery in the back
Engine/drivetrain:
Stock motor bored .030
forged pistons
Atr cam
port and polished LB4 heads
Port matched upper/lower intakes
#50 injectors
3 bar MAP
AFPR
Walbro 255
PT-54 turbo
custom cold air intake
Atr DP
EGR/cat/muffler delete
ATR Auxillary IC
Shurflo pump
3/4 rubber IC lines
Razor's alky kit
LM-1 wideband running through the stock ECM
Gilbert propshaft
Waller built 700r
2800 9/11
motorhome tranny cooler
TCI deep trans pan
gear reduction starter
purple wire replaced with 10 gauge from the brake booster down
Flyin Ryan
hated cuz he drives fords
Re: Post your FULL mod list.
Exterior
- 2" Goodmark cowl hood
- Tinted stock tail lights
- Typhoon power mirrors
- H4 Hella Euro spec glass housings
- Bi-xeon HID head lights (hi and low)
- OEM SS zr1 17x9.5" wheels silver with raptor tires
- Skultz billet 1.25" billet spacers for the rear
- Lund Backdraft spoiler
Interior
- Lotek 2 pod pillar
- VDO 30psi Boost gauge
- Cyberdyne digitial electric fuel pressure guage
- Innovative LM1 Wideband
- IBM Thinkpad a31 with datamaster 3.4.1
- Moates Xtreme ALLDL setup
- Pioneer head unit
- Pioneer speakers through out
- Alpine alarm with remote start
- Spare tire removed
- Jack and associated brackets removed
Eng. Drive.
- Powder coated black with red script upper intake slightly ported
- DIY front mount air2air
- RPM stage 1 turbo
- Non AC heater box
- A/C system deleted 100%
- March polished/powdercoated waterpump pulley
- Cone filter
- Cobra elbow
- Optima Red Top relocated to the bed
- 2 gauge wiring used through out
- Flaming river "big switch" disconnect
- Volvo 3000cfm efan
- Volvo Efan bracket kit
- SPAL PWM progressive fan controller and optional progressive temp sensor
- B&M Supercooler trans cooler
- All lines to transmission and cooler -an braided
- Billet afpr
- nallj92's Torque turnbuckle
- 3 bar map
- custom chip based off of a t1-18 ultimate bin
- Devilsown progressive meth injection
- Gilbert propshaft
- Detriot Turbo modified range selector for use with gilbert shaft
- Walbro intank 255lph pump
- 3" high flow cat
- Electric exhaust cutout on dp
- 3" custom exhaust from cat back
- Dynomax Ultraflow stainless round muffler
- ATR Blackbeatuie wires
- NGK UR5 plugs gapped @ 30
- Edelbrock alluminum waterpump
- Heater core ran to waterpump aux port on wp
- 140amp D1-CS144-GMT140 alternator
- Pas side fenderwell removed
- ABS Deleted
- Cruise control deleted
- EGR Deleted
- Vacuum ball deleted
- All vacuum lines replaced with red Baker silicone lines
- 180 tstat
- Braided heater core lines
- Belt tensioner deleted
- Misc brackets and bolts deleted
Suspension
- ATM Battlebars
- Bilstien shocks
- Bob Romano 2.5" blocks
* stock motor(valve covers have never been off)
* stock downpipe
* stock converter
* stock transmission
* scratches
* dents
* chips
* faded factory paint
* daily driven normally
*
I think that's it
Exterior
- 2" Goodmark cowl hood
- Tinted stock tail lights
- Typhoon power mirrors
- H4 Hella Euro spec glass housings
- Bi-xeon HID head lights (hi and low)
- OEM SS zr1 17x9.5" wheels silver with raptor tires
- Skultz billet 1.25" billet spacers for the rear
- Lund Backdraft spoiler
Interior
- Lotek 2 pod pillar
- VDO 30psi Boost gauge
- Cyberdyne digitial electric fuel pressure guage
- Innovative LM1 Wideband
- IBM Thinkpad a31 with datamaster 3.4.1
- Moates Xtreme ALLDL setup
- Pioneer head unit
- Pioneer speakers through out
- Alpine alarm with remote start
- Spare tire removed
- Jack and associated brackets removed
Eng. Drive.
- Powder coated black with red script upper intake slightly ported
- DIY front mount air2air
- RPM stage 1 turbo
- Non AC heater box
- A/C system deleted 100%
- March polished/powdercoated waterpump pulley
- Cone filter
- Cobra elbow
- Optima Red Top relocated to the bed
- 2 gauge wiring used through out
- Flaming river "big switch" disconnect
- Volvo 3000cfm efan
- Volvo Efan bracket kit
- SPAL PWM progressive fan controller and optional progressive temp sensor
- B&M Supercooler trans cooler
- All lines to transmission and cooler -an braided
- Billet afpr
- nallj92's Torque turnbuckle
- 3 bar map
- custom chip based off of a t1-18 ultimate bin
- Devilsown progressive meth injection
- Gilbert propshaft
- Detriot Turbo modified range selector for use with gilbert shaft
- Walbro intank 255lph pump
- 3" high flow cat
- Electric exhaust cutout on dp
- 3" custom exhaust from cat back
- Dynomax Ultraflow stainless round muffler
- ATR Blackbeatuie wires
- NGK UR5 plugs gapped @ 30
- Edelbrock alluminum waterpump
- Heater core ran to waterpump aux port on wp
- 140amp D1-CS144-GMT140 alternator
- Pas side fenderwell removed
- ABS Deleted
- Cruise control deleted
- EGR Deleted
- Vacuum ball deleted
- All vacuum lines replaced with red Baker silicone lines
- 180 tstat
- Braided heater core lines
- Belt tensioner deleted
- Misc brackets and bolts deleted
Suspension
- ATM Battlebars
- Bilstien shocks
- Bob Romano 2.5" blocks
* stock motor(valve covers have never been off)
* stock downpipe
* stock converter
* stock transmission
* scratches
* dents
* chips
* faded factory paint
* daily driven normally
*
I think that's it
Last edited:
Loeryder
New member
Re: Post your FULL mod list.
Exterior:
PPG Forest Green metallic repaint
Cladding repainted Audi Silver
painted mirrors and door handles body color
shaved roof rack, antenna, front plate and license plate lights
filled B pillar and C pillar body welds
Goodmark cowl hood
VIN etched glass
Interior:
Corbeau TRS racing seats
RK Kustom embroidered floor mats and utility mat
Tinted 20% all the way around
Lo-Tek 3 gauge pillar pod
Engine/Drivetrain:
massaged L35 heads w/LT1 hi-rev springs
port matched upper/lower intakes
TB bored to 52mm and bearing'd TB shaft
20G/14cm Mitsu turbo
JSM 3" DP
3k stall Hughes converter
Blake "built" 700R4
Spicer U joints
Gilbert Propshaft
SMC Alky injection
Ostrich ECM emulator
DIY WBo2
KB cold air kit
KB A/A
EGR delete
Wheels/Suspension:
Zo6 OE Concepts wheels 17 x 9.5
Michelin Pilot Sport 255/40 R17
Dustan Front Coilovers
JSM chromoly ball joint adapters
ZQ8 steering box / Borgensen needle bearing'd steering shaft
Bell Tech drop leafs
Bell Tech 1" drop block
ATR Rear sway bar
Baer 12" 4 wheel disk w/ Tucker ABS delete
Stereo:
Alpine HU
Infinity Kappa Series 4x6s and 6x9s
Alpine alarm
Exterior:
PPG Forest Green metallic repaint
Cladding repainted Audi Silver
painted mirrors and door handles body color
shaved roof rack, antenna, front plate and license plate lights
filled B pillar and C pillar body welds
Goodmark cowl hood
VIN etched glass
Interior:
Corbeau TRS racing seats
RK Kustom embroidered floor mats and utility mat
Tinted 20% all the way around
Lo-Tek 3 gauge pillar pod
Engine/Drivetrain:
massaged L35 heads w/LT1 hi-rev springs
port matched upper/lower intakes
TB bored to 52mm and bearing'd TB shaft
20G/14cm Mitsu turbo
JSM 3" DP
3k stall Hughes converter
Blake "built" 700R4
Spicer U joints
Gilbert Propshaft
SMC Alky injection
Ostrich ECM emulator
DIY WBo2
KB cold air kit
KB A/A
EGR delete
Wheels/Suspension:
Zo6 OE Concepts wheels 17 x 9.5
Michelin Pilot Sport 255/40 R17
Dustan Front Coilovers
JSM chromoly ball joint adapters
ZQ8 steering box / Borgensen needle bearing'd steering shaft
Bell Tech drop leafs
Bell Tech 1" drop block
ATR Rear sway bar
Baer 12" 4 wheel disk w/ Tucker ABS delete
Stereo:
Alpine HU
Infinity Kappa Series 4x6s and 6x9s
Alpine alarm
91blazins10
Active member
Re: Post your FULL mod list.
Exterior-
Clear turn signal lenses, black euro tails, blade of death, roof rack gone, rear wiper gone, darker painted cladding. Northeast rust mods.
Interior-
All new carpet with sound deadening, no spare tire, jack and tire iron replaced with a fire extinguisher, double gauge pod with wideband and boost gauge, and leds for alky. computer relocated to glove box, new shifter boot with red stitching, ultimate chip, greddy boost controller, all new floor mats from usspeed with silver typhoon embroidery.
Engine/Drivetrain-
JSM downpipe, atr exhaust, wastegate puck removed on stock turbo, shurflo ic pump hotwired, all rubber ic hose, 3bar, kennebell fpr, walbro 255, ngk ur6, taylor wires, conrad equivalent cap and rotor, rpm braided brake booster line,tb air foil, nallj92s engine tiedown, egr block off, cruise delete, vacuum ball delete, abs delete, a/c delete and bracket replaced with rpm pulley, hard turbo to ic pipe, intercooler and pipe covered with heat shielding, optima battery relocated further down with k&n filter above, razors alky injection, modified steering shaft with no more rag joint, 2800stall tq converter, deep finned tranny pan with drain plug, b&m tranny cooler, purple wire fixed, edelbrock highflow waterpump, 160degree tstat. gilbert propshaft.
Wheels/Suspension-
Camaro ss wheels with falken tires, lowered 2.5in upfront with loosing the torsion key bolts, 2in in the back with angled blocks,traction bars, kyb shocks all around, new sway bar bushings, rear sway bar, ls1 brakes upfront soon to be in the rear as well.
Stereo-
old pioneer receiver, clarion speakers upfront, kicker speakers in the back
Exterior-
Clear turn signal lenses, black euro tails, blade of death, roof rack gone, rear wiper gone, darker painted cladding. Northeast rust mods.
Interior-
All new carpet with sound deadening, no spare tire, jack and tire iron replaced with a fire extinguisher, double gauge pod with wideband and boost gauge, and leds for alky. computer relocated to glove box, new shifter boot with red stitching, ultimate chip, greddy boost controller, all new floor mats from usspeed with silver typhoon embroidery.
Engine/Drivetrain-
JSM downpipe, atr exhaust, wastegate puck removed on stock turbo, shurflo ic pump hotwired, all rubber ic hose, 3bar, kennebell fpr, walbro 255, ngk ur6, taylor wires, conrad equivalent cap and rotor, rpm braided brake booster line,tb air foil, nallj92s engine tiedown, egr block off, cruise delete, vacuum ball delete, abs delete, a/c delete and bracket replaced with rpm pulley, hard turbo to ic pipe, intercooler and pipe covered with heat shielding, optima battery relocated further down with k&n filter above, razors alky injection, modified steering shaft with no more rag joint, 2800stall tq converter, deep finned tranny pan with drain plug, b&m tranny cooler, purple wire fixed, edelbrock highflow waterpump, 160degree tstat. gilbert propshaft.
Wheels/Suspension-
Camaro ss wheels with falken tires, lowered 2.5in upfront with loosing the torsion key bolts, 2in in the back with angled blocks,traction bars, kyb shocks all around, new sway bar bushings, rear sway bar, ls1 brakes upfront soon to be in the rear as well.
Stereo-
old pioneer receiver, clarion speakers upfront, kicker speakers in the back
Last edited:
nello
Active member
Re: Post your FULL mod list.
Exterior-
Ty mirrors...later dumbos
Interior-
Guages for water temp, boost, and oil pressure...don't trust factory guages.
Intercooler toggle switch for water pump
Blitz III Boost controller
Engine/Drivetrain-
NEW:
fuel injectors
brakes
Silicone Vac lines
Wheel Cylinders
plugs
8.5 ignition wires
plug wire sleaves
cap and rotor
TCI deep tranny pan
boost, water, oil pres gauges by autometer
autometer 3-2/16 pod
ignition switch
starter
brake booster cable - RPM
K&N - RPM and self fabricated cool box
intercooler water pump - RPM
hoses all around, no more metal
homemade hotshot relay working perfect (cost me $5 instead of $40 so FU jegs)
Paint over rust on the chasis and underside...looks brand new again!
MSD coil from - RPM
fuel pump 255 high from - RPM
shurflow AFPR - RPM
Fuel pressure gauge on fuel rail - RPM
Derale Tranny cooler -Summit
chrome diff cover - Tucker auto
Wheels/Suspension-
New tires,
rear beltech sway,
new cheap shocks,
Re-cleared stock rims....actually still waiting to get them from the shop
Stereo-
Alpine 3 disc changer and speakers all around including the door speaker housing I keep seeing the Marlboro trucks.
Exterior-
Ty mirrors...later dumbos
Interior-
Guages for water temp, boost, and oil pressure...don't trust factory guages.
Intercooler toggle switch for water pump
Blitz III Boost controller
Engine/Drivetrain-
NEW:
fuel injectors
brakes
Silicone Vac lines
Wheel Cylinders
plugs
8.5 ignition wires
plug wire sleaves
cap and rotor
TCI deep tranny pan
boost, water, oil pres gauges by autometer
autometer 3-2/16 pod
ignition switch
starter
brake booster cable - RPM
K&N - RPM and self fabricated cool box
intercooler water pump - RPM
hoses all around, no more metal
homemade hotshot relay working perfect (cost me $5 instead of $40 so FU jegs)
Paint over rust on the chasis and underside...looks brand new again!
MSD coil from - RPM
fuel pump 255 high from - RPM
shurflow AFPR - RPM
Fuel pressure gauge on fuel rail - RPM
Derale Tranny cooler -Summit
chrome diff cover - Tucker auto
Wheels/Suspension-
New tires,
rear beltech sway,
new cheap shocks,
Re-cleared stock rims....actually still waiting to get them from the shop
Stereo-
Alpine 3 disc changer and speakers all around including the door speaker housing I keep seeing the Marlboro trucks.
Last edited:
JSM
Active member
Re: Post your FULL mod list.
1992 Typhoon #1295
Exterior
Painted cladding (black)
Interior
93 seats and overhead console
Custom glovebox emblem
Engine/Drivetrain
350 V8 9:6:1 compression
Twin GT35R turbos
Custom headers swain coated
3" dual downpipes
Wilson 90mm Throttle body
84# injectors
Twin Tial 38mm wastegates
-more
Prime Gears 4l80e
Transbrake
Custom 1 off parts inside
Billet shafts
not sure what other magic George put in it.
Wheels/Suspension
ZR1 sawblade wheels 11" Rear
4 link triagulated rear
Stainless coilover front
QA1 shocks
Hypercoil springs
Boxed in frame
Stereo
Empeg
2 PPI amps
1 Orion 225 HCCA
1 12" Orion sub in a spare tire looking round box
Line-X on floor, ceiling, walls
1992 Typhoon #1295
Exterior
Painted cladding (black)
Interior
93 seats and overhead console
Custom glovebox emblem
Engine/Drivetrain
350 V8 9:6:1 compression
Twin GT35R turbos
Custom headers swain coated
3" dual downpipes
Wilson 90mm Throttle body
84# injectors
Twin Tial 38mm wastegates
-more
Prime Gears 4l80e
Transbrake
Custom 1 off parts inside
Billet shafts
not sure what other magic George put in it.
Wheels/Suspension
ZR1 sawblade wheels 11" Rear
4 link triagulated rear
Stainless coilover front
QA1 shocks
Hypercoil springs
Boxed in frame
Stereo
Empeg
2 PPI amps
1 Orion 225 HCCA
1 12" Orion sub in a spare tire looking round box
Line-X on floor, ceiling, walls