Announcement

Collapse
No announcement yet.

User Profile

Collapse

Profile Sidebar

Collapse
Profile Picture
Mikeysy15
Last Activity: Yesterday, 10:14 PM
Joined: 12-09-2018
Location: San Fernando Valley , Ca.
  • Filter
  • Time
  • Show
  • Source
Clear All
new posts

  • Mikeysy15
    Mikeysy15 posted a Visitor Message for Vaders Sy
    I have an electronic boost controller . I have the turbosmart eboost electronic boost controller and it controls the spike much better then their manual .
    See more | Go to post

  • Mikeysy15
    Mikeysy15 posted a Visitor Message for Vaders Sy
    I have an rpm stage 1 turbo which is 50mm. Should of gone bigger but was scared of Lag . This thing spoils really fast . I hit 2nd gear before the 60ft mark at the track . Btw, what fuel filter do you use with the Stock fuel lines when you use e85. Or if you have different lines what size did you u...
    See more | Go to post

  • Mikeysy15
    replied to Syclone #1385 Stock turbo times
    Mph is still low and I think itís because my turbo is too small
    See more | Go to post

    Leave a comment:


  • Mikeysy15
    replied to Syclone #1385 Stock turbo times
    See more | Go to post

    Leave a comment:


  • Mikeysy15
    replied to Syclone #1385 Stock turbo times
    Your absolutely right , I went to Irwindale 1/8 mile track on Thursdayí. Didnít have time to buy race so I figured I would try with 3/4 tank of e85 and the rest 91 octane .
    Turned it up to 20lbs and the sputtered . Turned it down to 17 and ran a 7.46 but still didnít feel right. Then turned it...
    See more | Go to post

    Leave a comment:


  • Is this intercooler still for sale ?
    See more | Go to post

    Leave a comment:


  • Thatís great . Iíll PM you . Thank you...
    See more | Go to post

    Leave a comment:


  • RPM 90 degree sheet metal intake WANTED

    Hello guys, Iím looking for one of the old RPM 90 degree sheet metal intake that bolt up to a carb .
    My plan is to get a 2111 edelbrock manifold with injector
    bungs and bolt the intake on. I saw one sold here in 2013 . Iím just trying to compliment my ported L35 heads and 415 cam. If anybody...
    See more | Go to post

  • Mikeysy15
    replied to Syclone #1385 Stock turbo times
    Looks like itís running real good . Iíve screwed around with e85 a bit . I have the smaller 13 gallon and tank and Iíll add 5-6 gallons of e85 and the rest 91 octane . I turn up the boost to 17 on the street as well and get no knock. I have a turbotweak chip that I turn up 8 clicks on the dial which...
    See more | Go to post

    Leave a comment:


  • Mikeysy15
    replied to 90 degree sheet metal intake
    Sorry to bring back an old thread , but If anybody has one of these lying around That they want to sell. I will pay top dollar for it...
    See more | Go to post

    Leave a comment:


  • Mikeysy15
    replied to Finally the 11ís .
    Raced a brand new ZL1 with drag radials . Too bad he Red lighted because it would of been a great race . I was at his door the whole run...
    See more | Go to post

    Leave a comment:


  • Mikeysy15
    replied to Finally the 11ís .
    Went back to Irwindale last night , truck was running much better. Added some timing in via my scanmaster . Lowered my 75 dollar hankook tire pressure to 22 on all 4 corners and managed 2 runs in the 7.41 range and I hit 7.39 which was my fastest
    Manages two 1.58 60fts....
    See more | Go to post

    Leave a comment:


  • Mikeysy15
    commented on a Visitor Message From Mikeysy15
    Better launch . 7.39
    See more | Go to post

  • Mikeysy15
    Mikeysy15 posted a Visitor Message for Mikeysy15
    Went back to Irwindale last night , truck was running much better. Added some timing in via my scanmaster . Lowered my 75 dollar hankook tire pressure to 22 on all 4 corners and managed 2 runs in the 7.41 range and I hit 7.39 which was my fastest
    Manages two 1.58 60fts. Mph did not change but...
    See more | Go to post

  • Mikeysy15
    Mikeysy15 posted a Visitor Message for drhill
    Thank you sir , and yes In the 1/4 mile Iím absolutely shifting into OD which is whatís killing me . It makes no power after 4500. On the bright side , just got fully ported L35 heads back from the shop and Iíll be doing heads and cam in the next 2 months hopefully. Shift point should increase to ...
    See more | Go to post

  • Mikeysy15
    replied to Finally the 11ís .
    Forgot to add that raceweight is 3400lbs and DA was 2000. Stock engine with rpm stage 1 turbo and ATR upper intercooler and EBay heat exchanger only . Street tires .
    Front coilovers and caltrac monoleaf only. Truck has 32k original miles .
    See more | Go to post

    Leave a comment:


  • Mikeysy15
    started a topic Finally the 11ís .

    Finally the 11ís .

    Just can back from Autoclub Speedway in Fontana and. Broke into 11ís. Last time I went, my best was 12.1 at 108. My best this time was 11.8 at 111. I think I hit the turbos Effiency limit because I turned it up to 22psi and lost 1 tenth . 20psi is the limit on this little 50mm turbonectics . This...
    Best timeslip
    See more | Go to post
No activity results to display
Show More
Working...
X