Search results

SpeedInc input shaft. installed in tcase then removed due to project part out, still has its virginity...never seen an output shaft Billet magnesium adapter plate from the group buy here. i bolted it to a bare case for mock up and building the crossmember. that is all. would like to...

I have been holding onto these to use on my silverado but they ended up hitting the stock motor mounts so i used a set of flipped 2010 camaro manifolds instead. These are 1/2" mild steel flanges with all stainless sch10 pipe, fully tigged and back purged. they are t4 turbo flanges, with 38mm...

well, this didnt last long. due to a myriad of events in my life since november, i have decided to try to sell this. I hate to not finish it, but its just not in the cards right now, and hopefully someone else can pick up where I have left off...

I wrecked my 2001 2wd s10 recently and have begun the painful process of dismantling it for part out. It had a ton of really neat parts that i would like to utilize on my typhoon but the typhoon is in cold storage so i cant really test fit anything on it, so i am hoping you guys can help me...

Has anyone had their stock propshaft lengthened or is it standard to just buy a new one?

I have been mapping out all the wiring under the hood of my 93 typhoon for a few weeks now and i am stumped on a few things. Over the years, there has been a pretty significant amount of cutting and crimping done, so its been quite trying figuring it all out. if anyone can help with IDing...

I am in the middle of building my lsx conversion harness, so now is the time to do all my upgrades and changes to anything wired in the truck. I have found a couple of threads where people installed later model non-vacuum cruise control into their trucks. is this worth it? is there any...

I am building around a goal of approximately 750whp and running 17" non drag radial tires. Will I need the ability to ramp boost like a ams1000 does or is a simpler single target one like a aem tru boost good enough? I have an ams1000 in my s10 I can swap back and forth, but those require some...

This was installed on my ty when i got it. It is a large aftermarket a2a intercooler that bolts directly to the front frame rails. It is in good shape, all fins are nice and i repaired some of the lip that catches air. the outside is a little dirty but the inside is very clean. I will include...

Turbo was installed on a truck that sat outside for a long time. I ended up driving it around the block a couple times and it didnt smoke, or do anything bad. It made boost just fine. It has some side to side play, not enough to touch down. I measured end play at 0.010" $300

I couldn't really find a good answer for this, or a good step by step... Can I just pop off the front t-case cover, and pull the input shaft out and drop in the new one or is there more to it than that? I found the page with a ton of photos of rebuilding the case, but my ty has ~60k miles on it...

--Please read this if you are interested in any of my parts-- I do not have paypal. My preferred method to both buy and sell is postal money orders. they are about $1.50 plus $5.80 for a tracked flat rate envelope. I have been around the net for a long long time, using the same name, buying...

I just got this thing a couple weeks ago and planned to do up a nice 4.3 for it but after doing the research it just doesnt make sense to invest in a motor that has such limited options and high cost. $3000 for aluminum heads is more than i spent on my bbc pro actions 8 years ago. anyway, i...

Looking for an input shaft and adapter to put a 4l80e in my typhoon. I do not have paypal, i usually just mail PO money orders. Ill be out of town this coming week but will be ready to purchase on the 28th. thanks dave

Is a DFI Gen 6 with adapter harness worth anything? Long story short, it would be cheaper for me to cut the adapter harness up to install a megasquirt than to buy a 749 and associated bits to run code 59. unless that gen 6 and harness are worth anything. im guessing theyre worth exactly $0...

I signed up here a few weeks ago when i first started looking into getting a typhoon, and finally struck a deal and should be getting a 93 this weekend. i am pretty excited to start messing with it. I currently drive a 2001 S10 with a turbo aluminum block 4.8 ls. hopefully the ty can keep up...