tfink660
New member
Re: What did you do to your SY/TY today?
lol dont get me wrong i didnt mean it like that .. Im just anxious :0)
lol dont get me wrong i didnt mean it like that .. Im just anxious :0)
What did you do to your SY/TY today?
- Thread starter SloGN
- Start date
- Status
Re: What did you do to your SY/TY today?
installed 8k hid's in the fogs and polished the lips on the torq thrusts
installed 8k hid's in the fogs and polished the lips on the torq thrusts
aasltmike
Active member
Re: What did you do to your SY/TY today?
Finally got my ignition switch adjusted right so I got accessory power and ignition power. Also found some black hex head socket bolts to replace my centercap locks since you can't powder coat the chrome bolts. Also fixed my constant on ABS light and put a regular bulb back in instead of an LED bulb. Man, I hate re-attaching the HVAC temperature cable...:rant:
Finally got my ignition switch adjusted right so I got accessory power and ignition power. Also found some black hex head socket bolts to replace my centercap locks since you can't powder coat the chrome bolts. Also fixed my constant on ABS light and put a regular bulb back in instead of an LED bulb. Man, I hate re-attaching the HVAC temperature cable...:rant:
Chest Rockwell
Active member
Re: What did you do to your SY/TY today?
Actually took it for a drive yesterday, met up with a couple of locals. Can't wait for spring!
Actually took it for a drive yesterday, met up with a couple of locals. Can't wait for spring!
tfink660
New member
Re: What did you do to your SY/TY today?
what did you use on the Foglamps? Factory housings or aftermarket? Which Bulbs? And i had to remove my factory switch it burned up and melted. so ill have to run my own switch to a relay and out when i do my fog HID's
what did you use on the Foglamps? Factory housings or aftermarket? Which Bulbs? And i had to remove my factory switch it burned up and melted. so ill have to run my own switch to a relay and out when i do my fog HID's
92TYPHOON937
Active member
Re: What did you do to your SY/TY today?
took some stuff off the top of it that it had gathered from sittin
took some stuff off the top of it that it had gathered from sittin
Sean Krupa
Moderator
Re: What did you do to your SY/TY today?
Got my DutchTy Intercooler from wtlivezey today. Ofcourse I had to start polishing it. I will polish it more before the install. I'm going to install it in the summer so I can Datalog the temp difference. This is a excellent piece! Thanks DutchTy for making these:tup:
Got my DutchTy Intercooler from wtlivezey today. Ofcourse I had to start polishing it. I will polish it more before the install. I'm going to install it in the summer so I can Datalog the temp difference. This is a excellent piece! Thanks DutchTy for making these:tup:
92TYPHOON937
Active member
Re: What did you do to your SY/TY today?
nice
nice
Neelsonwheels
Donating Member
Re: What did you do to your SY/TY today?
Installed my new hood prop kit that I got from Philntex.
It is a very nice kit and super easy to install.
Installed my new hood prop kit that I got from Philntex.
It is a very nice kit and super easy to install.
Re: What did you do to your SY/TY today?
Started installing my belltech 2/2 kit
Started installing my belltech 2/2 kit
qbnkiller
Conflaguration Specialist
Re: What did you do to your SY/TY today?
Assembled the short-block. Waiting for head gaskets, timing set, and balancer.
Removed old Accel ignition system and coil. Started installing new MSD ignition system and coil. Cleaned up wiring a bit...more to go. Ordered 1/2" vent for fuel system to prevent vapor lock issues from last year (grrrrr).
Assembled the short-block. Waiting for head gaskets, timing set, and balancer.
Removed old Accel ignition system and coil. Started installing new MSD ignition system and coil. Cleaned up wiring a bit...more to go. Ordered 1/2" vent for fuel system to prevent vapor lock issues from last year (grrrrr).
NJSERRANO
New member
Re: What did you do to your SY/TY today?
1. Installed new Walbro 255 pump and Racetronix hot wire kit.
I had some detonation under 1/2 throttle, which I thought was caused by kenne bell chip. Then,, the truck had a little trouble starting for about a week, then finally failed to turn over one night. It runs SO much better now. Only problem now is the fuel gauge reads FULL all of the time
2. Installed Typhoon mirrors, haven't wired thenm up for power yet.
I found a typhoon clone that was being parted out. I grabbed 2 mirrors, wiring harnesses/connectors, a stereo bezel and ash tray for $60!
3. "Ain't Nobody's Bizness" Tint was installed...looks GOOD!
1. Installed new Walbro 255 pump and Racetronix hot wire kit.
I had some detonation under 1/2 throttle, which I thought was caused by kenne bell chip. Then,, the truck had a little trouble starting for about a week, then finally failed to turn over one night. It runs SO much better now. Only problem now is the fuel gauge reads FULL all of the time
2. Installed Typhoon mirrors, haven't wired thenm up for power yet.
I found a typhoon clone that was being parted out. I grabbed 2 mirrors, wiring harnesses/connectors, a stereo bezel and ash tray for $60!
3. "Ain't Nobody's Bizness" Tint was installed...looks GOOD!
QuinnSY
Donating Member
Re: What did you do to your SY/TY today?
Tint looks really good! What % is it? I have been wanting to do mine, but I got pulled over 2-3 times a month in my old truck with only 35%.. Living in LA sucks in the car customization world...
Also if you don't mind, I would like to meet up with you one of these days and measure out and take notes on the power mirror harness and make my own I have the mirrors and the adjustment switch also, but no harness!
1. Installed new Walbro 255 pump and Racetronix hot wire kit.
I had some detonation under 1/2 throttle, which I thought was caused by kenne bell chip. Then,, the truck had a little trouble starting for about a week, then finally failed to turn over one night. It runs SO much better now. Only problem now is the fuel gauge reads FULL all of the time
2. Installed Typhoon mirrors, haven't wired thenm up for power yet.
I found a typhoon clone that was being parted out. I grabbed 2 mirrors, wiring harnesses/connectors, a stereo bezel and ash tray for $60!
3. "Ain't Nobody's Bizness" Tint was installed...looks GOOD!
Tint looks really good! What % is it? I have been wanting to do mine, but I got pulled over 2-3 times a month in my old truck with only 35%.. Living in LA sucks in the car customization world...
Also if you don't mind, I would like to meet up with you one of these days and measure out and take notes on the power mirror harness and make my own
I have the mirrors and the adjustment switch also, but no harness!
NJSERRANO
New member
Re: What did you do to your SY/TY today?
The tint is 5%. Oh yeah, I have the under dash adj. switch too. As far as harness is concerned, I only have the wiring from the motor with connectors. I would need to lengthen those wires and connect them into my fuse panel to gain power. Here's the info on a conversion that I found...
http://www.sytyarchives.com/howto/v..._name=mirror_control_install.php&dir=interior
Give me a shout sometime 817-992-1890
Tint looks really good! What % is it? I have been wanting to do mine, but I got pulled over 2-3 times a month in my old truck with only 35%.. Living in LA sucks in the car customization world...
Also if you don't mind, I would like to meet up with you one of these days and measure out and take notes on the power mirror harness and make my own
The tint is 5%. Oh yeah, I have the under dash adj. switch too. As far as harness is concerned, I only have the wiring from the motor with connectors. I would need to lengthen those wires and connect them into my fuse panel to gain power. Here's the info on a conversion that I found...
http://www.sytyarchives.com/howto/v..._name=mirror_control_install.php&dir=interior
Give me a shout sometime 817-992-1890
- Status