Recent content by ls1monza

Re: Cylinder head and intake manifold options...please help Motor number one...(good heads with factory type short block) is on the stand. i pulled the intake off and test fit the standard port intake...whew! the port location isnt too far off but the raised runner heads have a wider bolt...

Re: Cylinder head and intake manifold options...please help Yeah.....I was already planning on building a set of headers....I bought some really cool Stainless steel parts from the guys at ARH.....The factory block engine has alot of great valvetrain parts and I was hoping on using the...

Re: Cylinder head and intake manifold options...please help I have always thought those people at Katech were the gurus of these motors in the 1980s... :( They built this motor and chose those small heads for it....I havent taken the engine apart yet..but the build sheet suggests 280 cubic...

Re: Cylinder head and intake manifold options...please help Here you go!! Good luck....and thanks

Re: Cylinder head and intake manifold options...please help lol.....I tried....Kael is retired and Jason(his son) was 10 years old then.....they have no archive info that far back... :( The numbers dont cross anywhere....I'll take a pic and post it. Maybe you guys can help....yay!

Re: Cylinder head and intake manifold options...please help Thats a good idea......and Im not on the LUV boards ..YET!! Thanks for the replies guys. Id hate for the RR heads to go to waste...but someone will buy them....

Re: Cylinder head and intake manifold options...please help Cmon!!! Nobody has ANY knowledge of what is required to install a standard port intake manifold(like stock Syclone intake) on the "raised runner" heads?! :dunno::dunno:Do I need to buy a Syclone just to deserve any response? I AM...

I have two v6 engines and wanted to take all of the best parts from both and build one to go in my truck...The question I have is regarding which heads to use. The first choice is a set of ported GM "raised runner" 23 degree heads. They are fresh,complete and ported(essentially all new good...

Re: Fuel Injection help...Please Thanks for the feedback. The heads are 14044883 castings. So, how many differences are there between the 2000 V6 and a 1990 one? For fuel injection swappage. The computer out of the 2000 is the same as a 1999-2002 Camaro...

Re: Leaking injector o-rings I believe all EV1 injectors use the same o-rings. They're most likely in stock at your local auto parts store. I'd go buy a new set if it were me.

I am attempting to swap around a few projects that will enable me to install a 4.3V6 into an S-10 or Sonoma. Right now the motor is carb'd with the giant "box-ram" intake. It is a nightmare for throttle repsonse and tip-in fueling. My plan is to go EFI. The questions I have are...... 1. What EFI...

Re: Leaking injector o-rings Can you move all of the connectors side to side? If they feel tight you may be binding on one preventing the rail from sitting evenly . Sometimes it helps to slowly and methodically tighten in an "X" pattern while wiggling them.

Re: Trailblazer SS rapage I see nothing wrong with what you said. Your truck is obviously fatser than a low 14....I would suppose the gauges up his pillar were for looks. Honestly, I have never seen a 4wd one and would assume they are much slower considering they have the same motor and much...

Re: Trailblazer SS rapage I'm not a moderator. I cannot see edited posts to know what was so "no-so nice"....Nobody ever called anyone nieve.(I don't think...certainly not me)....Once again... 1.This isn't a lesson on how much better TBSS's are then SyTy's 2.I didn't bash anyone about their...

Re: supercharged 2k cheby truck... Re: supercharged 2k cheby truck... Is that near the Lake or on the other side of I35? that's a bummer about the hangout scene. Dallas still is pretty popular;but it's mostly Hwy.....Lately, The weather hasn't permitted......but today is turning out to be...