Search results

Re: 4l80e wiring? the speed sensors are on the external wire harness to the TCI computer and the temp sensor is integrated into the internal wiring harness. I doubt that could be caused by my wiring, but you never know! I think I'll move the grounds directly to the battery to start with, and...

Re: 4l80e wiring? I guess the reason I'm confused is that I figure there would be a switch in the program to change it form a positive signal to a grounded signal, and I can't find anything related to this in the tci program. Should the box be configured correctly to begin with? It is...

Re: 4l80e wiring? yea, it is red with the round style connector. So does this mean that I can just hook the brake lite wire to the f terminal on the ALDL? I think I might also try running my grounds back to the battery. there are tied up under the dash with a few other grounds so I might be...

Hey guys, I finally finished rebuilding my 4l80e and got it in the truck. I think I have most of the wiring tied into the stock computer, I just need to finger out the tcc part of the wiring. I read that the older tci units need a relay on that circuit, and then I have read that its not...

Re: Need interior screws I wold be in if you wanted to do a GB on a complete interior set! All of mine are nasty!

Re: Ostrich HELP! I had similar problems this my ostrich when I first got it. I went round and round with the the thing until I tried a new set of batteries! Confirm that every thing is hooked up properly first, but don't rule out the batteries! Later Jeremy

Re: A1000 bleeds off too fast? Aw man those fittings are bad a$$< Ive been wanting to do that for a while now. Do you have a list of the fittings that you used and where you got them? Thanks, Jeremy

Re: Which torque converter for 80e What do you guys think of this converter on e-bay? I'm getting to the point where I'll need the tc soon. I'm not trying to be a cheap a$$, but would like to get a converter that will hold up. Also what stall speed should I run with the build below: Stock...

Re: Intercooler to throttle body connector for the stock water to air system I think it is just a 4" silicone sleeve connector. cheap on e-bay.

Re: Exhaust. oh man that has to be one of the dumbest things I've ever seen! http://www.rdfabs.com/galleries/index.php?level=picture&id=487 I assume there is a divider between the two sections there, but it has got to heat the air Jeffin' hot!!

Re: PCS Customer Service How was the filter causing problems? I'm starting my 4l80e swap and plan to reuse my remote filter That I used with the 700, is this somehow going to cause problems for me? Thanks, Jeremy

Re: best way to keep motor cool I think I have a safari fan and very lightly used clutch hub. I went to electric to free up some room. If you need it make an offer. later

Re: Who has personally rebuilt a 4l80e Yea that write up is awesome!! I've got just about every book there is on 4l80e's and this write up has info I just haven't seen elsewhere. thanks for sharing!!! My 4l80e is disassembled in my shop waiting for parts to rebuild. Thanks, Jeremy

Re: 4l80e Gurus HELP!! the 1997 and up transmissions don't need the lube holes. 1996 and prior years need the lube holes.

Re: 4l80e Gurus HELP!! Just an update! I talked to the guys over at PACT and they said in this situation they would weld the holes form the inside of the shaft, just don't get it too hot. I had some time to play this morning so I taped up all the bearing surfaces, and wrapped a wet towel...

Re: 4l80e Gurus HELP!! it seams that all Georges old posts are gone? Do you have any more information on this? Thanks

Re: 4l80e Gurus HELP!! Also, Just a thought and may be totally off base here, but if the intermediate shaft is not hollow there would not be any pressure on the lube holes of the output shaft. wold the holes even make any difference? I assume they would as there were two different shafts...

Re: 4l80e Gurus HELP!! yea, its on the side of the shaft I was thinking that the hole was the only difference. Do you think that this can just be plugged and how? I was thinking I could carefully weld the holes shut below the surface of the shaft or from the inside, but the shaft has...

Re: 4l80e Gurus HELP!! I'm not real sure what the difference is. I was unaware that there was a difference until this morning when I read it in the instructions I got with the kit. I have the tranns pulled apart I'll do a closer inspection and take pictures when I go home for lunch in a few...

I'm in the process of swapping a 4l80e into my ty. I have a late model (1998) 4X4 4l80e, tci controller, and the swap kit that I bought form 1BADV6. I also have started collecting parts to rebuild the trans myself. The problem is that the kit I have has the early model output shaft and I need...