Search results

Hey guys. I don't get on here nearly as much as I used to, but I still lurk around. We had a few SyTy.net customers at www.RacePartSolutions.com today. And, although most of the old timers and our regular customers know the drill, I thought this might be a good opportunity to thank our current...

Anybody know approximately what a complete Syclone cab weighs (doors, interior and glass all intact)? I'd like to pull the cab completely off to clean and "puff can detail" the frame rails while I'm replacing the the body mount bushings. Is this something a couple of guys can lift and move...

Anybody know where I can get or purchase a Syclone wiring diagram / schematic? I searched and found some old links, but they're no longer online. I have an aftermarket ECM and harness for the new engine. I wish to eliminate as much of the old wiring as possible, while retaining just chassis...

If any of you guys buy stuff from racepartsolutions.com, the discount code to get 10% off is "0001". You can give them the code as a walk-in customer, over the phone, or on internet orders. This works for everybody; you don't need to have an account with them or be a licensed shop to get the...

Has anybody actually broken, or have direct knowledge of breaking, anything other than an axle in a stock rear end?

I've got an odd 4L80e controller question: Looking to swap a 4L80e into a non-computer controller forced induction application. I would like a controller to be mappable off of both throttle position and MAP (if that's possible). I am very weary of TPS based controllers on turbo cars, because we...

It appears these types of electric pumps are used in some oem applications. This particular unit has been retrofitted to an Oldsmobile, running both the power steering and hydroboost brakes. Anybody have any experience with these...

It has been rumored that a certain OG SyTy nut is selling his C5 'Vette, and is looking into repurchasing a certain Sy that he used to own...since the Syclone in question does not currently have a running driveline, the person in question is contemplating stuffing an all-aluminum 414", twin...

I ran my C5 against my old Sy. I lined up against Tony and he pulled a few cars out of the hole. His truck has a built motor with ported L35s, a Crane Compucam and a 20g TD06H. It took me until 3rd gear to pass him... it would have been close if it were an 1/8th mile race. However, my FRC 'Vette...

It has been quite a while since I've been on this website. I just wanted to update the SyTy community about the status of these trucks that I've previously owned... Sy #2596 is now owned by Tony Indiviglio. We recently built up the motor with Eagle rods, SpeedPro pistons, Crane cam, ARP studs...

I have a buyer interested in Sy #2596. He contacted the loan office at his bank, but they do not finance older vehicles. Can anybody recommend SyTy friendly lender? TIA, Rob

What's the deal with Dr. Nice? Has the board administration gone hardcore, or have we been hacked?

We all met at Jack's place today; thanks for having us over. Everyone loved Jack's 5 speed Sy...what a sweet ride :wink: I can't wait 'til Wednesday when we meet again at Moroso. Later, Rob <font size=-1>[ This Message was edited by: RAACCR on 2002-03-10 22:09 ]</font>

I installed the Mitsu 20G, along with one of Brandon's HD propshafts. I set the boost at 14#, and went for a drive to check things out. Within a few minutes, I ran across a V-8 Dodge Dakota with an aftermarket exhaust. We were rolling along about 60mph; he dropped back about a car length, then...

Many of you know that I took a little break from my original Sy after the new motor broke several driveline components early last year. In order to stay involved in the SyTy world, I purchased another Sy from a fellow list member and long-time friend, and I've been busy getting back to basics...