Search results

Alright, the time has come where the wife and myself need to let a toy go. The first to the chopping block is the Sy unfortunately. This really saddens me, the hours I've put into the truck and the enjoyment I've had with it makes it hard. But...it will help our situation currently and make...

...heading west, then north on a side street. Real clean, tinted rear window. I was driving the wife in her pontiac grand am. Anyone here? Just checking. This was on Friday...the 26th

Is there a diagram that shows which wire is the correct #? Or anything similar? I tried search, perhaps it ownz me...

I was wondering if a bad O2 sensor was the only way to throw 44. This is what I did before hand; verified 0 deg TDC, did leak down bike tube trick-no leaks found. Although I don't have DM handy the truck was run with DM before and the O2 volts were going crazy. Would a bad O2 sensor be the...

Ok guys- First list of mods: PTE 52 w/ cat ATR Exhaust Ultimate Chip 3 Bar Map AFPR EGR Removed Ron's Fuel Pump Jabsco Pump Relocated Intercooler Lines Recent Conrad Cap/Rotor, Plugs & Wires What I did before the test: Disconnected Intercoller Pump Fuel Pressure Set to 30psi, lots of stumble...

After lots of miles in the sun my gauge needles are practically yellow. Has anyone stripped the needles or re-applied orange paint on the backside of the needle to restore the look? I'm thinking testors orange may work...any advice or suggestions would be appreciated. Thanks guys!

Just wondering for pinstripe removal...thanks.

Does anyone have pics of the welded lower intake for the conversion with '98 and up vortec heads? I know Smeagol has done it this way...anyone else? I guess I like the idea of the intake being welded, rather than the aluminum inserts. Thanks guys. Brandon

Is anybody running the Optima Red Top in the ATR Battery Relocation Kit? I'm looking for new juice and wanted to make sure it fit before I went ahead and purchased it. Thanks.

Ok guys...I'm pissed, The battery on my Sy dies all of the time, maybe 10 times now. Anyways, It seems as though the security system installed by the previous owner is messed up. Here's what happens: I purposely do not turn on the alarm, for fear of it glitching. Whenever I'm not around...

Ok guys- The truck has plenty of mileage at 114,000. The engine has 75,000 on a warranty replacement. I know that's alot and a rebuild is a must. But money is a concern. I was just wanting some input on the possible problems. Here is the problem, as I'm driving around it doesn't appear to...

he guys- help, I'm stuck at work.... I was drying out my door jams and accidently hit the latch that goes up when the doors are closed to lock the door. How do I get them down so I can close my doors for the drive home...ahh!!

Hey all- This really isn't a dispute just a check of my vin#. The guy I bought my Sy from said it was a '91. The registration form the state of Illinois says it's a '91. My Insurance agent however tells me his computer says it's a '92. I said no way, there's only 4 proptotypes for '92, or...

Hi guys- Recently I've added a bunch of goodies, most are in my sig., but the most extensive are the PTE Turbo kit, Ultimate chip, fueling upgrades etc. My question is this: With the chip set at T1 15, flooring the truck, I'm only seeing 11 lbs. of boost tops. In daily driving conditions if...

Hi guys- A question, I installed the autometer electronic FP gauge. When I turn the truck on the fuel pressure gauge reads where it should, it's when I turn the truck off the gauge reads all the way to 100 psi , as opposed to 0. Did I install a wire incorrectly or is it the gauge? Thanks.

Ok guys- Here's what it does...when driving normally it shifts fine up through OD. Once I'm driving in OD at 50 mph around 1800rpm the truck starts to surge or feel like it's kicking out of OD. I know the OD in the Ford's AOD would do this when the OD band was on its way out. Is this...

With the vaccum line off of the regulator, I set FP to 52psi, as per ghettosleds's recommendation with the ultimate chip, when I installed the vaccum line, FP dropped to 40 psi. I thought it was only suppose to drop 2-3 psi? So I readjusted FP with no vaccum line, setting FP at 55 psi, with...

Anyone here? It was about 11:30 last night, black with dual chrome 3 inch exhaust tips straight out the back. Just checking...looked nice, at least from a distance.

Does anyone have detailed instructions/pics on how to install a transmission cooler. I was wondering where you run the lines into the tranny? Or do you run the lines into the radiator and then use the stock lines going back to the tranny. TIA.

Does anybody have a good suggestion on how to remove pinstripping? The thin one line pieces aren't a problem, it's this nasty multilined border running along the whole truck right above the cladding. The previous owner had no taste in my opinion. Any suggestions would be greatly appreciated.