Epstyphoon303
1992 Typhoon #2019
Re: Boost control cutout relay??
What can I replace the stock up pipe with? I do not like the way it fits on there.
What can I replace the stock up pipe with? I do not like the way it fits on there.
Boost control cutout relay??
- Thread starter Epstyphoon303
- Start date
wildphil
I Love My Ty's
Re: Boost control cutout relay??
The cheapest would be to buy a radiator hose and cut it to fit.
Some of the SyTy vendors have them made for this.
If you are loosing air from this pipe. There is no way to build the correct boost.
The cheapest would be to buy a radiator hose and cut it to fit.
Some of the SyTy vendors have them made for this.
If you are loosing air from this pipe. There is no way to build the correct boost.
dgoodhue
BuSTeD 4.3
Re: Boost control cutout relay??
What chip do you have? The Ultimate chips usually needed the wastegate rod to be tightened. My stock Sy with an Ultimate pretty much made base boost in 1 and 2 gear with the stock wastegate rod adjustment.
While it may be frustrating, I don't think it's a waste of time verifying the turbo boost control operation given the age of SyTy's.
What chip do you have? The Ultimate chips usually needed the wastegate rod to be tightened. My stock Sy with an Ultimate pretty much made base boost in 1 and 2 gear with the stock wastegate rod adjustment.
While it may be frustrating, I don't think it's a waste of time verifying the turbo boost control operation given the age of SyTy's.
Epstyphoon303
1992 Typhoon #2019
Re: Boost control cutout relay??
I'm pretty sure its the stock chip. The truck used to pull hard but I can't remember if it started actin up before or after I replaced the boost control solenoid. I was changing the lines and accidentally broke the tip off the old one that goes to the waste gate. I have power to the orange wire on the solenoid with the key on. I also took off the solenoid and was able to blow through it. So I'm clueless at this point.
I'm pretty sure its the stock chip. The truck used to pull hard but I can't remember if it started actin up before or after I replaced the boost control solenoid. I was changing the lines and accidentally broke the tip off the old one that goes to the waste gate. I have power to the orange wire on the solenoid with the key on. I also took off the solenoid and was able to blow through it. So I'm clueless at this point.
Epstyphoon303
1992 Typhoon #2019
Re: Boost control cutout relay??
Dave there you are I was waiting for a response haha thanks buddy I will do so in the am.
Dave there you are I was waiting for a response haha thanks buddy I will do so in the am.
Epstyphoon303
1992 Typhoon #2019
Re: Boost control cutout relay??
Hey dave the test turned out good, solenoid is ok and working. Im pickin up a new wastegate actuator on saturday so hopefully it helps. If not then its off a cliff for the ty hahaha just kidding.
Hey dave the test turned out good, solenoid is ok and working. Im pickin up a new wastegate actuator on saturday so hopefully it helps. If not then its off a cliff for the ty hahaha just kidding.
Last edited:
Throws
Active member
Re: Boost control cutout relay??
New can? Really? From GM? How much did it set you back?
-P
New can? Really? From GM? How much did it set you back?
-P
Throws
Active member
Re: Boost control cutout relay??
Me or Epstyphoon303?
Boost Gauge? Just going off of what DataMaster is showing as boost. AFAIK, this should be accurate(ish). Right?
Sotck chip? OK... you got me there... I'm making assumptions based on my observations (and what DM is showing as the ID on the chip).
Waste movement? This is next. I was waiting on a another actuator from a member here before pulling the fenderwell liner out. I'm hearing 7/8th overlap. Right?
Pics? I can do that later.
As far as overlooking something simple... I'm in IT. We overlook the simple stuff all day long.
-P
Me or Epstyphoon303?
Boost Gauge? Just going off of what DataMaster is showing as boost. AFAIK, this should be accurate(ish). Right?
Sotck chip? OK... you got me there... I'm making assumptions based on my observations (and what DM is showing as the ID on the chip).
Waste movement? This is next. I was waiting on a another actuator from a member here before pulling the fenderwell liner out. I'm hearing 7/8th overlap. Right?
Pics? I can do that later.
As far as overlooking something simple... I'm in IT. We overlook the simple stuff all day long.
-P
Throws
Active member
Re: Boost control cutout relay??
NP. We've both been going after our "low boost" issues in a similar fashion. Frustrating when a proposed fix does nothing (or at least has no net effect).
-P
NP. We've both been going after our "low boost" issues in a similar fashion. Frustrating when a proposed fix does nothing (or at least has no net effect).
-P