FL Head/cam/intake/turbo package for sale

blk00z28

blk00z28

Forced to by choice
This is a package deal.
You will need a few miscellaneous parts and very little work to complete the top end and make it a bolt on.

Bowtie Heads
p/n 1404883 (Raised runner 23*)
60cc chamber
2.00 intake, 1.60 exhaust (don't remember make, sorry)
Comp 98541 dual springs
Viton 11/32 Seals
Jesel shaft mount 1:6 rockers

Flow (i/e)
6" - 280 - 205

Porting, polishing, push rod area enlargement, and assembly were done by Champion. Valve cover rail was milled thinner to allow better intake fitment. Brand new rocker mounts and rocker rebuild kit(bearings, bolts, clips, etc.).

Parts included:
- ARP head studs
- Cometic Head gaskets
- RPM sheet metal perimeter valve covers(don't have gaskets)
- Billet weld on oil filler

Brodix Intake
p/n - 10093314
Injector bungs welded in
It has been milled and runners welded to "raise" the port to match the heads. You will need to mill the runner gasket surface and at the very least polish the port weld. Also mill an "angle" or "vertical" cut into the flange face to allow valve covers to fit on the heads correctly without interference.

Parts included:
- Matching fuel rails
- Intake gaskets
- RPM sheet metal 100 degree sideways facing plenum
- Standard 90 degree forward facing plenum
- 90mm Accufab throttle body
- (6) used 75# low impedance injectors

New Comp Cam
gross lift(i/e)
.538 - .531
Duration(i/e)
224/224
Separation 115.

Parts included:
- Comp Lifters for 4.3L
- Edelbrock double roller timing chain

Turbo
Garrett T76 GTQ
Ball bearing center section
Water cooled
PTE exhaust housing (.85 a/r 3" outlet)
Polished compressor
If memory serves me correctly, the exhaust housing was ceramic coated by Nolan
Wastegate port has been enlarged as well by Nolan.

Everything you read I have invested over $6k into. The parts I include alone are over $2k, that's not including heads, intake, or turbo only.
Info on what it took to make the intake work and pics of heads/intake:
http://www.syty.net/forums/showthread.php?t=74314

You will not find a better, cheaper package then this for what I include in the offer. Any questions or pictures of anything just ask. If I missed anything I will post it in a reply in here.

Asking $4,800 obo + shipping(and insurance on shipping) + paypal fees.
 
blk00z28

blk00z28

Forced to by choice
Re: Head/cam/intake/turbo package for sale

Gatman said:
Can you please send me some photos of the above mentioned parts. I'm in Ocala and have cash in fist. Email me at: Boosted6@Rocketmail.com
Glenn
Click to expand...
I'll post them here in case anyone else wanted pics. Only pic I didn't get was of the head gaskets, they are in another box and didn't pull them out.

Heads, rockers-stands and rocker rebuild kit, arp studs, intake, turbo, valve covers, timing chain, lifters, plenum's, tb, placer, fuel rails, injectors, intake gaskets, intake bolts(which I just found and am throwing in) oil filler bung(2 of them..) and weld on an fitting male ends(throwing in as well):
885133CD-FC72-4716-B1AA-5AEF48D08514.jpg





Turbo p/n plate:
0BBB9C4D-F120-459C-AB3C-2B6A819F0BDC.jpg.html
0BBB9C4D-F120-459C-AB3C-2B6A819F0BDC.jpg.html


WG hole dim's to show enlargement and how big:
EDB9D4C5-5544-4C2B-9706-2D9B4F9EF6E3.jpg.html


Cam card:

cam.jpg.html
 
Z SKI

Z SKI

Donating Member
Re: Head/cam/intake/turbo package for sale

Hey Tim!!! Nice stuff you got there.. GLWS
 
blk00z28

blk00z28

Forced to by choice
Re: Head/cam/intake/turbo package for sale

No idea. I just got them with that flow number.
 
blk00z28

blk00z28

Forced to by choice
Re: Head/cam/intake/turbo package for sale

The intake rockers are, not sure how much, I'd have to really dig for the email from Jesel about the specs. Seen here:

 
TYTILIDIE

TYTILIDIE

METH HEAD
Re: Head/cam/intake/turbo package for sale

Make sure you let anyone interested in this know that they have to run a solid roller set up. They'll need offset lifters as you can't run offset rockers on hydraulic roller. The ports are so big you have to go around them. I literally have the EXACT same set up.
 
blk00z28

blk00z28

Forced to by choice
Re: Head/cam/intake/turbo package for sale

Not necessarily true.

If the heads were set up to run a stud mount rocker then yes, they would require offset lifters and guides to match for a correct push rod angle. BUT if you notice in the pictures 2 replies down(which come directly from the link I supply in the first sale post for additional pictures). The intake rocker has the offset built in and the push rod location of stock. Requiring only to measure for the correct length of a rod.

Believe you me. (all reading this questioning the purchase) I did my homework on this set up. I spent years gathering info to do it right once. No, it is not a normal set up due to the raised runner design, no one likes to use a raise runner because you have to do what I've done to the intake to make it work. But it is 90% done for you. I could have bought used $150 rockers and thrown them on. But I didn't. I spent $1,100 for Jesel to send me the stands, and bolts with bearings to rebuild the rockers so it was done right.

I incline you all to look into what built heads run. Even the cost of ported built Vortecs not to mention aluminum heads even running standard rockers. This intake, is the intake from Roberts build he first went 8's on. It is not ported. That gives you some idea of the flow it can handle. You will see this is one hell of a deal that hardly comes around for such a price. Everyone wants to go fast, but no one wants to spend the money to do it. I did it, and am now offering it to everyone for an extremely fair deal because I unfortunately need the money for my family. I will not lower the price again.

Price is firm at $3,800 plus shipping/fees.

ps; to stop the pm's from those of you offering trades, I don't need anything.
 
TYTILIDIE

TYTILIDIE

METH HEAD
Re: Head/cam/intake/turbo package for sale

Hmm, everyone I talked to said you can't put side load on hydraulic lifters. Upon installing the cam and the hydraulic lifters (standard centered pushrod) the pushrod didn't clear the intake port, I too am running offset Jesel rockers. Something to think about.

At any rate, its a great price especially if it is all ready to go. Just sharing my experience. I can't wait to see how mine performs. GLWS
 
blk00z28

blk00z28

Forced to by choice
Re: Head/cam/intake/turbo package for sale

TYTILIDIE said:
Hmm, everyone I talked to said you can't put side load on hydraulic lifters. Upon installing the cam and the hydraulic lifters (standard centered pushrod) the pushrod didn't clear the intake port, I too am running offset Jesel rockers. Something to think about.

At any rate, its a great price especially if it is all ready to go. Just sharing my experience. I can't wait to see how mine performs. GLWS
Click to expand...
The pushrod openings have been enlarged also on the heads.
 
9

90pgt

Donating Member
Re: Head/cam/intake/turbo package for sale

seem like a pretty legit deal, if i wasn't already selling 2 sets of heads my self id buy it lol.
 
randy merritt

randy merritt

Donating Member
Re: Head/cam/intake/turbo package for sale

Tim, PM me your phone number. I have a couple of questions and may be interested in buying this.

Randy
 
blk00z28

blk00z28

Forced to by choice
Re: Head/cam/intake/turbo package for sale

randy merritt said:
Tim, PM me your phone number. I have a couple of questions and may be interested in buying this.

Randy
Click to expand...
I pm'd you Randy. I didn't get the notification that you had replied to this post, sorry for the delay. :tup:

Bump for sale, original buyer hasn't contacted me since about payment. So parts are still for sale.
 
S

syco1962

Donating Member
Re: Head/cam/intake/turbo package for sale

blk00z28 said:
I pm'd you Randy. I didn't get the notification that you had replied to this post, sorry for the delay. :tup:

Bump for sale, original buyer hasn't contacted me since about payment. So parts are still for sale.
Click to expand...

if you are going to split up maybe interested in cam lifters and timing chain
 
You must log in or register to reply here.
Top