Lt1 Nitrous Plate on a SyTy?
- Thread starter tarzan
- Start date
James Thomas
"NO CLASS"
Re: Lt1 Nitrous Plate on a SyTy?
You going to spray NOS or use this for Meth? If you are going to try this for meth injection it wont work, not enough pressure to atomize properly and will just kind squirt out. Even though most meth systems are running 80+ psi, NOS nozzel's are set up for 900 + PSI tank pressure. For NOS, should be ok I think.
__________
James
You going to spray NOS or use this for Meth? If you are going to try this for meth injection it wont work, not enough pressure to atomize properly and will just kind squirt out. Even though most meth systems are running 80+ psi, NOS nozzel's are set up for 900 + PSI tank pressure. For NOS, should be ok I think.
__________
James
James Thomas
"NO CLASS"
Re: Lt1 Nitrous Plate on a SyTy?
Shouldn't be a problem for NOS use. Just remember that boost magnifies NOS. I.E. 25 shot with boost is more like 35-40. Use the smallest jets you can get and go in 5hp steps, no joke. It can be done and with good results but the old "this 25 shot is ok so lets bump it to 50" will get you a broken engine before you can pull your foot out of it. Check your data logs ultra close and pull the plugs after EVERY run. Don't even try it unless you have full gauges specially WB and fuel, EGT is highly recommended. Just go real slow and careful. We run it on top of the blowers and it does have the Dr. J and Mr. Hyde ups and downs but DAAAYYYMMM when it’s right!
Good luck!
Shouldn't be a problem for NOS use. Just remember that boost magnifies NOS. I.E. 25 shot with boost is more like 35-40. Use the smallest jets you can get and go in 5hp steps, no joke. It can be done and with good results but the old "this 25 shot is ok so lets bump it to 50" will get you a broken engine before you can pull your foot out of it. Check your data logs ultra close and pull the plugs after EVERY run. Don't even try it unless you have full gauges specially WB and fuel, EGT is highly recommended. Just go real slow and careful. We run it on top of the blowers and it does have the Dr. J and Mr. Hyde ups and downs but DAAAYYYMMM when it’s right!
Good luck!
Flyin Ryan
hated cuz he drives fords
Re: Lt1 Nitrous Plate on a SyTy?
"Nitrous is like a hot girl with STD's. You know you wanna hit it, but you're affraid of the consequences!"
"Nitrous is like a hot girl with STD's. You know you wanna hit it, but you're affraid of the consequences!"
Re: Lt1 Nitrous Plate on a SyTy?
James,
Thanks for the advice, I went that VERY route with the NO2 kit I have on my GN. Started off with a 25 shot, and have since worked my way up to a 50. I ran it rich for awhile, and ATE plugs like candy....but the motor is still going strong, and I finally have it LOVING the kit. Its nice to not have to stall as hard on the line, holding down the temps, and using the kit to still spool it immediately out of the gate
. I'm gonna try running stock converter, with a small shot first....Figure its worth a shot
-Will
James,
Thanks for the advice, I went that VERY route with the NO2 kit I have on my GN. Started off with a 25 shot, and have since worked my way up to a 50. I ran it rich for awhile, and ATE plugs like candy....but the motor is still going strong, and I finally have it LOVING the kit. Its nice to not have to stall as hard on the line, holding down the temps, and using the kit to still spool it immediately out of the gate
. I'm gonna try running stock converter, with a small shot first....Figure its worth a shot -Will