Project Insanity... 1st street video
- Thread starter Syclone0565
- Start date
Tooky
Serious about performance
Re: Project Insanity... 1st street video
I've got that video and several others. :tup:
JSM
Active member
Daron
Active member
Syclone0565
CustomMulticades.com
Re: Project Insanity... 1st street video
It's all good
Nothing broke. Just working out a few little things and will be heading to the track the 13th.
It will run fine the way it is. I just want to polish it up a little.
Lots of videos after the track day.
:tup:
It's all good
Nothing broke. Just working out a few little things and will be heading to the track the 13th.
It will run fine the way it is. I just want to polish it up a little.
Lots of videos after the track day.
:tup:
Syclone0565
CustomMulticades.com
Re: Project Insanity... 1st street video
Yes I am running a Stage 5 RPM Transmission. Don't even think about trans issues any more
Yes I am running a Stage 5 RPM Transmission. Don't even think about trans issues any more
Syclone0565
CustomMulticades.com
Re: Project Insanity... 1st street video
Sorry, Here is the link http://www.rpmtransmissions.com/ and yes it is a 4L80E that will take everything I am going to through at it. 1400+hp
The owner is a very nice guy and he is the guy that bough Denny Rabbs truck (Syclone).
He drives a twin turbo C6 vette himself and can take care of you while you wait if you prefer it. If you have any more questions just ask.
Thanks
Sorry, Here is the link http://www.rpmtransmissions.com/ and yes it is a 4L80E that will take everything I am going to through at it. 1400+hp
The owner is a very nice guy and he is the guy that bough Denny Rabbs truck (Syclone).
He drives a twin turbo C6 vette himself and can take care of you while you wait if you prefer it. If you have any more questions just ask.
Thanks
JKsSyclone
Active member
Re: Project Insanity... 1st street video
Is it a 5.3 or a 6.0??? I though the LQ4 & LQ9 are 6.0's & the LM7 was the 5.3.:dunno:
Is it a 5.3 or a 6.0??? I though the LQ4 & LQ9 are 6.0's & the LM7 was the 5.3.:dunno:
JKsSyclone
Active member
Re: Project Insanity... 1st street video
Cool! So its a LM7. I was just confused...It doesnt take much.:lol:
Cool! So its a LM7. I was just confused...It doesnt take much.:lol:
Syclone0565
CustomMulticades.com
Re: Project Insanity... 1st street video
I have a fully built 5.3 iron block ls motor.
Block was cleaned up and debured and is now a 364cu.in.
Compstar crank
Compstar rods
Mahle pistons coated top and sides
calico coated bearings
every bolt ARP
ALUM ported/polished Heads flows over 300CFM
Comp cam Specs: 224/230 - 155 LS - .610 lift
I have a fully built 5.3 iron block ls motor.
Block was cleaned up and debured and is now a 364cu.in.
Compstar crank
Compstar rods
Mahle pistons coated top and sides
calico coated bearings
every bolt ARP
ALUM ported/polished Heads flows over 300CFM
Comp cam Specs: 224/230 - 155 LS - .610 lift
Re: Project Insanity... 1st street video
If your gonna put built peices in there why not a stroker?
If your gonna put built peices in there why not a stroker?
JuStBlAzIN
Active member
Re: Project Insanity... 1st street video
Did you do your own harness? Or whos are you using? And which computer are you using to control it all?
Did you do your own harness? Or whos are you using? And which computer are you using to control it all?
Six-is-Enough
Use to do a little Boost
Re: Project Insanity... 1st street video
It is a stock ls1 ecm using tunerpro. I think he did the harness himself too.:tup:
It is a stock ls1 ecm using tunerpro. I think he did the harness himself too.:tup: