What did you do to your SY/TY today?
- Thread starter SloGN
- Start date
- Status
Fighting5thSVT
Active member
Re: What did you do to your SY/TY today?
Finally got my plates and put them on!
[/IMG]
Finally got my plates and put them on!
SloGN
9Sec Alky V6
Re: What did you do to your SY/TY today?
well i started it up to make sure the battery wasn't dead and hooked the scanner up to it and veried that everything is ok. well of course the day i load it on the trailer it will goof-up.
Can a sy be towed on jack-stands while sitting on the trailor.:tup:
well i started it up to make sure the battery wasn't dead and hooked the scanner up to it and veried that everything is ok. well of course the day i load it on the trailer it will goof-up.
Can a sy be towed on jack-stands while sitting on the trailor.:tup:
2500avalanche
Well-known member
Re: What did you do to your SY/TY today?
Painted my just fixed cladding from Mark! Just got the clear on it. Going to post pics tonight mounted!
Painted my just fixed cladding from Mark! Just got the clear on it. Going to post pics tonight mounted!
![Quickstop [UK]](/forums/data/avatars/m/5/5165.jpg?1570199786){kind=avatar}
Quickstop [UK]
Combating adversyty.
Re: What did you do to your SY/TY today?
was that magazine related?
Installed:
lower CCHE
March water pulley
upper Waller intercooler and rerouted hoses
new front wheel hub seals
oil pressure gauge
corrected dash wiring fault (bezerk)
adjusted shifter linkage for trans
fixed broken horn
reinstalled transmission lines
adjusted A arms for coilover
installed overflow bottle
hydroboost brake pedal (TYTILIDIE)
and boost launched my working truck for the first time in 3 years!!!!!
Videos to follow!
was that magazine related?
Installed:
lower CCHE
March water pulley
upper Waller intercooler and rerouted hoses
new front wheel hub seals
oil pressure gauge
corrected dash wiring fault (bezerk)
adjusted shifter linkage for trans
fixed broken horn
reinstalled transmission lines
adjusted A arms for coilover
installed overflow bottle
hydroboost brake pedal (TYTILIDIE)
and boost launched my working truck for the first time in 3 years!!!!!
Videos to follow!
Number219GT
Broke Status
Re: What did you do to your SY/TY today?
Sat in it and made "VROOOM" noises. Haha. Looked at it, then thought; "Damn, this thing needs a major tune-up".
Sat in it and made "VROOOM" noises. Haha. Looked at it, then thought; "Damn, this thing needs a major tune-up".
incognito
stocker
Re: What did you do to your SY/TY today?
cleaned some more, the under carriage is filthy, utterly disgusting. i have to pull the bed, it is just way too dirty. installed rear shocks and front wheel spacers, found out i need longer studs.
need to clean my garage, it too is a wreck. bunch of windy storms here lately has caused a bunch of small particulate to gather on the floor. annoying.
cleaned some more, the under carriage is filthy, utterly disgusting. i have to pull the bed, it is just way too dirty. installed rear shocks and front wheel spacers, found out i need longer studs.
need to clean my garage, it too is a wreck. bunch of windy storms here lately has caused a bunch of small particulate to gather on the floor. annoying.
2500avalanche
Well-known member
Re: What did you do to your SY/TY today?
Put the cladding on that I painted for the 1st time (Front arch, rocker, rear corner - all drivers side), how does it look? SOrry, its dusty!
Put the cladding on that I painted for the 1st time (Front arch, rocker, rear corner - all drivers side), how does it look? SOrry, its dusty!
2500avalanche
Well-known member
Re: What did you do to your SY/TY today?
The back piece was a PIA! It took me a while to get that one piece. I broke 2 pieces of the rear tab area, of course the part that wasn't reinforced!
One was a section that connects to teh round discs, and the other was the bottom part where it mounts to the wheel well.
I saved them!
Oh well.
But I have everything else!
It confuses me because on the rear corner there looks like provisions for 2 bolt holes, but on the arch there is only 1.
Maybe that is how they all are?!?!
The back piece was a PIA! It took me a while to get that one piece. I broke 2 pieces of the rear tab area, of course the part that wasn't reinforced!
One was a section that connects to teh round discs, and the other was the bottom part where it mounts to the wheel well.
I saved them!
Oh well.
But I have everything else!
It confuses me because on the rear corner there looks like provisions for 2 bolt holes, but on the arch there is only 1.
Maybe that is how they all are?!?!
Captain Morgan
Moderated User
Re: What did you do to your SY/TY today?
looks good....... for a Pittsburgh fan
looks good....... for a Pittsburgh fan
sy2206
New member
Re: What did you do to your SY/TY today?
We're talking about that triangular shaped area where the arch meets the rear corner. On the corner, there's supposed to be two small little alignment pins, and one hole in the center. On the rear arch, there's supposed to be three holes(two for the alignment pins, one for the bolt in the middle). The clip nut goes on the arch, and the 6mm bolt goes up through the corner into the arch/clip nut. The only time I've ever put the rear corners on, I've pulled the wheel arch, installed the corner, then put the wheel arch back on.
We're talking about that triangular shaped area where the arch meets the rear corner. On the corner, there's supposed to be two small little alignment pins, and one hole in the center. On the rear arch, there's supposed to be three holes(two for the alignment pins, one for the bolt in the middle). The clip nut goes on the arch, and the 6mm bolt goes up through the corner into the arch/clip nut. The only time I've ever put the rear corners on, I've pulled the wheel arch, installed the corner, then put the wheel arch back on.
2500avalanche
Well-known member
Re: What did you do to your SY/TY today?
hmmm, allignment pins? You have a pic what they look like?
The clip is there
hmmm, allignment pins? You have a pic what they look like?
The clip is there
- Status