What did you do to your SY/TY today?
- Thread starter SloGN
- Start date
- Status
92TYPHOON937
Active member
Re: What did you do to your SY/TY today?
i drove it around today went to a car show friday evening with it and going to a car show tom
i drove it around today went to a car show friday evening with it and going to a car show tom
turbodog
Donating Member
Re: What did you do to your SY/TY today?
When R&R'ing the evaporator coil, I pulled the right front wheel to access the evap housing screws. discovered (another) split CV boot. So, today I replaced the cv shaft. The coilovers make that a 20 minute job. Cool. But, when I installed the JS tubular a-arms and CBR front brakes, I had a big reduction in steering lock. I think in removing the steering stops, I went overboard, and that's why I keep splittingn CV boots.
When R&R'ing the evaporator coil, I pulled the right front wheel to access the evap housing screws. discovered (another) split CV boot. So, today I replaced the cv shaft. The coilovers make that a 20 minute job. Cool. But, when I installed the JS tubular a-arms and CBR front brakes, I had a big reduction in steering lock. I think in removing the steering stops, I went overboard, and that's why I keep splittingn CV boots.
SloGN
9Sec Alky V6
Re: What did you do to your SY/TY today?
Wow this thread is a yr old now.
I replaced the belt tensioner today with a unit that i got at the pick a part. i have the non oem ones:rant:
I now gotta start the cleaning process again it's time for the Autofair cleaning week to begin.
Wow this thread is a yr old now.
I replaced the belt tensioner today with a unit that i got at the pick a part. i have the non oem ones:rant:
I now gotta start the cleaning process again it's time for the Autofair cleaning week to begin.
Richard Le
New member
Re: What did you do to your SY/TY today?
I replaced the fried section of my purple starter wire. I barely tugged on it and the little ring terminal at the starter snapped:
New section of 10-gauge wire:
New ring terminal:
Thermo-sleeve to reflect away the heat from the header and downpipe:
The end result:
I replaced the fried section of my purple starter wire. I barely tugged on it and the little ring terminal at the starter snapped:
New section of 10-gauge wire:
New ring terminal:
Thermo-sleeve to reflect away the heat from the header and downpipe:
The end result:
1madgumby
New member
Syclone#1992
SyTy.net Moderator
Re: What did you do to your SY/TY today?
Started mine today, let it run for a while, and then covered it back up and lost the keys....was able to find them (they were on the tonneau cover). LOL.
Started mine today, let it run for a while, and then covered it back up and lost the keys....was able to find them (they were on the tonneau cover). LOL.
SYCLONE#1531
'MOFOFAST
Re: What did you do to your SY/TY today?
I scraped the shoe polished dial in#s off of my windows!!!
I scraped the shoe polished dial in#s off of my windows!!!
Sean Krupa
Moderator
Re: What did you do to your SY/TY today?
What times did you run? Did you take any videos? I like watching the videos of your Sy at the track.
I scraped the shoe polished dial in#s off of my windows!!!
What times did you run? Did you take any videos? I like watching the videos of your Sy at the track.
Ian Turgeon
Cascading Inspiration
Re: What did you do to your SY/TY today?
Swapped the passenger side RPM valve cover for a vortec one, now both are the same.
Swapped the passenger side RPM valve cover for a vortec one, now both are the same.
escofield
New member
Re: What did you do to your SY/TY today?
Put most of the cladding back on, still need to do the doors and the rockers tomorrow when I borrow a rivet gun.
Still having trouble figuring out how this goes on the fender for arch.. I just have the "S" bracket bolted to the cladding and to a hole in the fender.
Put most of the cladding back on, still need to do the doors and the rockers tomorrow when I borrow a rivet gun.
Still having trouble figuring out how this goes on the fender for arch.. I just have the "S" bracket bolted to the cladding and to a hole in the fender.
Chest Rockwell
Active member
Re: What did you do to your SY/TY today?
Sold the one that started it all for me. (sniffle sniffle) Now I get to focus on the Syclone and have some fun.
Sold the one that started it all for me. (sniffle sniffle) Now I get to focus on the Syclone and have some fun.
1madgumby
New member
Chest Rockwell
Active member
WyoSyclone
Active member
Re: What did you do to your SY/TY today?
That's not part of the cladding or bumper supports that I can see.... it looks familiar, I just can't remember where I've seen it??
Put most of the cladding back on, still need to do the doors and the rockers tomorrow when I borrow a rivet gun.
Still having trouble figuring out how this goes on the fender for arch.. I just have the "S" bracket bolted to the cladding and to a hole in the fender.
That's not part of the cladding or bumper supports that I can see.... it looks familiar, I just can't remember where I've seen it??
1madgumby
New member
- Status