Recent content by J-bird

Re: Holley dominator efi knock sensor interference? Ok, I have the main power for the Domiator hooked directly to the battery, but i have the accessory power to the dominator and MSD ignition hooked up to the same key on power circuit. I have the msd ignition and dominator both grounded to...

Re: Holley dominator efi knock sensor interference? ha, thanks for the bump. I had forgot about this and saw the thread again. On closer inspection I do believe that my msd is hooked up to the power junction on the firewall where some of the other stuff for the dominator is hooked up as well...

Re: Holley dominator efi knock sensor interference? Thanks for the replies! I will check out the links. Steve Morris' guys did the initial start up tune for me, I'll see what they have to say about it! thanks,

I saw Randy's post below and did not want interfere with his post. I have my domiator efi set up and running enough to drive the truck, but I'm having issues with the knock reporting. I always have knock counts, even when the sensor is unplugged! I have been on the Holley tech forum a wile...

Re: FS 84# Injectors, SBC Fuel Injection Intake, two GT35 Turbos Do you have any pictures of the intake? is if a forward facing TB or side? how does this compare to an edelbrock 2114? S**t, never-mind. reading is important! not a v6 intake Thanks!

Re: Mark Williams 32 Spline input shaft group purchase Try # 2 I'll call dibs if its still available! let me know and Ill PP the payment!

Re: 11.97 @ 112 on 10-12 lbs of boost I Got my dominator from Hood a few weeks back and will start on the install after I finally get my pte turbo installed & some other misc projects done. Do you have any tips on the removal of the stock harness(what to leave and what to remove). The...

Re: Mild bowtie build Awesome Denny!!! Can't wait to hear how it goes!

Re: 4l80e wiring? yea, I wish I could go and and beat on it for a while! Still breaking in the new motor, then I'll install my pte 6776rsp turbo, then tune again, and then, and then. I think I now have way too much motor for the waller 57mm that I'm running now for break-in. I really having...

Re: 4l80e wiring? I feel like a real dumb ass now, but I finally got this thing working. I turns out that the program in my tci box was bad. I bought the TCI TCU used and I thought it had the program from George Blake in it already. after going trough the setup wizard it shifts like a champ...

Re: 4l80e wiring? As i was cutting the old harness out I left the volt meter hooked up to the pins 1-4(12volt+) and pin 54(sensor ground), as I cut the ground wires form the tps and rpm the continuity went away. I'm really scratching my head as to what I have done now! I'm waiting on a friend...

Re: 4l80e wiring? soon!! I did order the harness so maybe by the weekend I'll be on the road!!!!

Re: 4l80e wiring? That's what I'm thinking. may have to wait a few more days to get that one. I have been spending too much on guns and ammo lately! Too many expensive hobbies, not enough money or time! Later,

Re: 4l80e wiring? I think I may have finally got this thing fingered out! I have been real busy with work for the past few moths, and taking a break form the ty let me look at it with fresh eyes yesterday. Anyways I think I have a short in my harness form tci. I was checking the harness...

Re: hp evo's I think they would look horrible!!!! j/k I have been wanting to get a set of those for my ty in the worst way, just can't justify putting new wheels on a truck that hasn't moved more than 50miles in the past year and half. Ebay seems to have some doesn't prices on them...