Search results

Re: Holley dominator efi knock sensor interference? Ok, I have the main power for the Domiator hooked directly to the battery, but i have the accessory power to the dominator and MSD ignition hooked up to the same key on power circuit. I have the msd ignition and dominator both grounded to...

Re: Holley dominator efi knock sensor interference? ha, thanks for the bump. I had forgot about this and saw the thread again. On closer inspection I do believe that my msd is hooked up to the power junction on the firewall where some of the other stuff for the dominator is hooked up as well...

Re: Holley dominator efi knock sensor interference? Thanks for the replies! I will check out the links. Steve Morris' guys did the initial start up tune for me, I'll see what they have to say about it! thanks,

I saw Randy's post below and did not want interfere with his post. I have my domiator efi set up and running enough to drive the truck, but I'm having issues with the knock reporting. I always have knock counts, even when the sensor is unplugged! I have been on the Holley tech forum a wile...

Re: FS 84# Injectors, SBC Fuel Injection Intake, two GT35 Turbos Do you have any pictures of the intake? is if a forward facing TB or side? how does this compare to an edelbrock 2114? S**t, never-mind. reading is important! not a v6 intake Thanks!

Re: Mark Williams 32 Spline input shaft group purchase Try # 2 I'll call dibs if its still available! let me know and Ill PP the payment!

Re: 11.97 @ 112 on 10-12 lbs of boost I Got my dominator from Hood a few weeks back and will start on the install after I finally get my pte turbo installed & some other misc projects done. Do you have any tips on the removal of the stock harness(what to leave and what to remove). The...

Re: Mild bowtie build Awesome Denny!!! Can't wait to hear how it goes!

Re: 4l80e wiring? yea, I wish I could go and and beat on it for a while! Still breaking in the new motor, then I'll install my pte 6776rsp turbo, then tune again, and then, and then. I think I now have way too much motor for the waller 57mm that I'm running now for break-in. I really having...

Re: 4l80e wiring? I feel like a real dumb ass now, but I finally got this thing working. I turns out that the program in my tci box was bad. I bought the TCI TCU used and I thought it had the program from George Blake in it already. after going trough the setup wizard it shifts like a champ...

Re: 4l80e wiring? As i was cutting the old harness out I left the volt meter hooked up to the pins 1-4(12volt+) and pin 54(sensor ground), as I cut the ground wires form the tps and rpm the continuity went away. I'm really scratching my head as to what I have done now! I'm waiting on a friend...

Re: 4l80e wiring? soon!! I did order the harness so maybe by the weekend I'll be on the road!!!!

Re: 4l80e wiring? That's what I'm thinking. may have to wait a few more days to get that one. I have been spending too much on guns and ammo lately! Too many expensive hobbies, not enough money or time! Later,

Re: 4l80e wiring? I think I may have finally got this thing fingered out! I have been real busy with work for the past few moths, and taking a break form the ty let me look at it with fresh eyes yesterday. Anyways I think I have a short in my harness form tci. I was checking the harness...

Re: hp evo's I think they would look horrible!!!! j/k I have been wanting to get a set of those for my ty in the worst way, just can't justify putting new wheels on a truck that hasn't moved more than 50miles in the past year and half. Ebay seems to have some doesn't prices on them...

Re: Help me pick a cam! that says that it is a flat tappet cam will this work with roller lifters?

Re: Help me pick a cam! http://www.summitracing.com/parts/EDL-3714/ What are the chances that this would work, the lift is .488 on the exhaust side. It's not a good top end cam like I would want in a car that only weighs 2000lbs fully loaded, but it's mile better than the stock cam.

Re: Help me pick a cam! Can I use an after market spring and get more lift without cutting the heads? or is it necessary to cut the heads on all non stock springs?

Fist off this is not syty related so mods please move if this is not the appropriate section. I have been helping my brother build a lotus super seven over the past year, using some take off parts my ty and junk yard parts (budget build). We have finished the frame, suspension and brakes, and...

Re: What is your Intake Air Temp while on the highway? Do you still have an egr? That is what i noticed on my ty when cruzing, after egr delete temps would stay down at cruz.