Search results

I have a slightly ported 2111 edelbrock intake for your stock heads or L35 heads. It was purchased from RPM . The only thing you would need is the upper plenum. Has fuel rails and brackets . Looking for 650 shipped.

My last track day before I go to the bigger cam and better heads ........ and now probably a bigger turbo . This shit doesn’t end . So today I went multiple high 9 second passes but the truck was falling off pretty bad at the 1000ft mark. As soon as I made the first pass at 27psi and the stock...

Just came back from the track . Had 2 Good licks since I don’t have a roll cage . Truck went 6.29 at 111mph with a warning to slow down and then I sent it with 30psi and a 14psi launch and it went 6.09 at 112.5 with a 1.39 60ft. Track was really good , Da was really good . About 400 over sea...

Just want to give people a heads up out there so they don’t go through what I went through . If you decide to install solid motor mounts from Sportmachines be aware that the driver side lowers your motor about an inch further down. I Have rpm headers and the SM’s steering shaft and I installed...

Went to a private track rental at our local 1/8 mile track . Really didn’t know what to expect . DA was 2000-2500 all day. This pass was the last one. They let me slide with 6.60-6.40 passes because it was a private event but when I hit the 6.39 they called me to the tower and told me I needed...

Looking for a 58mm Rpm TB to finish my setup. Thank you .PM me or let me know . Can call me at 818 381-7265 . Mike .

Last week I sold my 6262 and purchased a 6466 from ( proptop) a well know member on here . He’s really helped me a lot with my truck and I’d like to say he’s one of the most solid guys I’ve talked to. If your looking to make 25psi or more on e85 or race gas then this is the turbo for you. I...

I got a RPM stage 1 turbo and the cold air intake . 600 shipped for both . Turbo will connect to your stock downo

Does anybody know what NGK spark plug can be used for L35 heads that are 2 steps colder then stock . I was using UR6 but I need colder plugs as these are getting hot under high boost . I purchased 6 brand new BR7EF but the thread is longer . Would that matter ? Plugs are for E85 . Any help would...

Stock factory intake, top plenum , fuel rail with adjustable fuel pressure regulator for sale . 400 shipped for everything . Don’t need this anymore because I have the RPM setup .

Only 1 run today on the new setup . Powerglide trans , 3.08 gears , 28x10.5 M/T full slick . I ran out of gear and had to let off about 150ft because I was bouncing off the rev limiter and scanmaster showing knock . Converter is still to loose . Footbrake at 3000rpm and 25psi on e85 . PTE 6262...

Just wanted to point out that I installed the RPM manifold and plenum and it really woke up the engine past 4500 rpm . It shifted the powerband of the truck another 1000 -1500 to the right . This was with a PTE 6262 at 23psi on e85. But beware gentlemen. I was ok on fuel before the manifold swap...

Recently bought a brand new SM propshaft with the linkage and had it on the car for about 4 days . Found out my transfer case was bad so converted the car to RWD . Don’t need this anymore . Will do 380 shipped . It cost me 460 just a month ago. Call me or text me at 818 381-7265 . Ask for Mike...

Hello everyone , Just wanted to send out my information about the new turbo I installed and the difference in power . I haven’t made a pass yet in the 1/4 mile with the new turbo only 1/8 mile . I also wasn’t able to turn it up over 20psi because I got kicked out . So with my RPM stage 1 I ran a...

I was wondering if anybody was running an RPM stage 3 turbo. I know PTE is the way to go but I would need a downpipe and don’t know where to find one . I know it’s a 60-1 turbo but need to see what size the exhaust side is . I have the RPM Stage 1 now and it’s a good little turbo that spoils...

Hello guys, I’m looking for one of the old RPM 90 degree sheet metal intake that bolt up to a carb . My plan is to get a 2111 edelbrock manifold with injector bungs and bolt the intake on. I saw one sold here in 2013 . I’m just trying to compliment my ported L35 heads and 415 cam. If anybody...

Just can back from Autoclub Speedway in Fontana and. Broke into 11’s. Last time I went, my best was 12.1 at 108. My best this time was 11.8 at 111. I think I hit the turbos Effiency limit because I turned it up to 22psi and lost 1 tenth . 20psi is the limit on this little 50mm turbonectics ...

Just wanted to comment that an F body aluminum driveshaft is a direct bolt on for a Syclone . Same exact length . I simply took mine off and installed the aluminum f body on. Same teeth on the tranny shaft and all. I paid 120 bucks . It was 4lbs lighter and it eliminated a lot of the vibration...

I was just wondering the effects on removing the front swaybar on our cars . I’ve done this on all my previous rwd to hook better on launch and for weight transfer . Also the weight reduction is nice . This is my first Awd truck so I’m just wondering if it would help or actually not help ...