Search results

Re: 5 gal Ice heat exchanger need to get up to 25 posts so I can put some parts up for sale in the sales forum. My job takes up so much of my time (truck driver).:cry: anyone not able to see the pics in the links Ive posted?

Re: 5 gal Ice heat exchanger I'm using a kenne bell cold air box that uses sheet metal to block off hot under hood air from the fender where the k&n filter draws cool air. No longer using the ATR kit, only have about 6 feet of hose under the hood (3 feet coming in and 3 feet going out) both...

Re: 5 gal Ice heat exchanger https://www.dropbox.com/s/sa955h9v0kosr0a/20160417_184628.jpg?dl=0 https://www.dropbox.com/s/mqval05cwm32dbb/20160417_184637.jpg?dl=0 couple of more pics. Yea I have thought of using large gel packs along with bagged ice. Didn't think of the bottles of frozen...

Re: 5 gal Ice heat exchanger https://www.dropbox.com/s/ou6v51i06casr6b/20160321_183726.jpg?dl=0 https://www.dropbox.com/s/cnv1mg9zf4kuwye/s-l1000.jpg?dl=0 I'll take some photos this weekend and post more.

Re: 5 gal Ice heat exchanger Actually I am using both, Spraying 1210cc's of vp fuel M1 on 93 octane. I'm using a heat exchanger with a 10" 2100cfm electric fan during street use. All mounted away from under the hood. Completely wrapped the original IC in thermotec heat shield to prevent (or...

Re: 5 gal Ice heat exchanger tried to upload pictures but it failed.

Recently installed one of these in the bed running the lines thru the front passenger fender, using 20# of bagged ice I was able to monitor intercooler water temps fall to 33 degrees while the engine was running. Now looking into placing a metal canister filled with dry ice into the box, of...

Looking for advise on my next turbo, right now I'm using a Mitsu TDo6 25G 12cm with a journal bearing. Engine mods are 206 roller 114LS, ported Vortecs with Milodon megaflow stock size valves, Forged 8.5:1 pistons, eagle rods, Billet crank, 4bolt mains, lower 1/3 block fill, built 700r4, stock...

Re: FS: Aluminum Intercooler Scoops payment sent

Re: FS: Intercooler scoops - Update 05/25/10 any news on another run?

Re: Idle from Hell Looks like a possible success. Went back one more time reset the IAC valve, and cleared the ecm again. Reconnected the IAC plug and started up the engine. Using my left hand to keep the throttle open, I gradually turned the idle set screw back out until it was at .61 on the...

Re: Idle from Hell Took a few minutes to start it up and write down the #'s for you guys. Also since this is a Velosyty chip it allows the user to manually adjust the fuel trim. On the few times the truck idled well I noticed the AFR was between 11:1-12:1 when it was Ideling badly it pegged the...

Re: Idle from Hell Don, the IAC # when it was at its best idle was 41. Bad idle was at two extremes 00 and around 90. The distributor, coil, cap, rotor, ngk plugs, magnecore 10mm wires are all new. Checked the vacuum lines replaced with new silicon hose. All new intake and TB gaskets.

Re: Idle from Hell It seems now after I installed the new IAC valve even resetting the ecm makes no improvement. Only idles well if I reset the IAC and then unplug it leaving it unplugged. Also noticed that this new IAC valve makes a different noise while resetting a ticking noise where the...

ok guys this one is for the site gurus. Did the search for this topic already, and followed what I had found to no avail. Here is the situation, engine runs fine down the road both part throttle and wot. Problem is when I come to a stop it runs like total crap no matter if in park or in gear...

Didn't find what I was looking for so if someone could please answer this for me. Which of the two ports on the back of the intercooler is the return line from the heat exchanger. My truck has a ATR pump and additional exchanger using heater hoses instead of the factory lines. Just looking into...

Re: any Ideas? thanks for the advice gentlemen.

Re: any Ideas? Found the problem, its a good idea to quit working on things when your too tired. I had mistakenly hooked up the 2 ground wires from the wire loom at the rear of the alternator to the post on the back of the alternator. The wires I found that burned up were the ground wires to...

Hello everyone, was finishing up an engine rebuild. Marked all the wires so I could place them all back in order. Hooked up the new battery, walked around to the passenger door and the entire cab was filled with smoke. Dash gauges and console were lit up without the key in the ignition. Using...