Turbo Blankets: update SYTY PROTOTYPE PICS

[93ty475]

Re: same here

Re: same here

.... hope we can get something going with a pte setup as well...

I hope the same for the RPM downpipe I have as well . Whos making these ? Didnt I read that the guy doing these left that company ?

julio supposedly left the company for bigger and better things ... www.insultech.com

 

[93ty475]

Re: same here

Re: same here

:1gun: :repost:

 

[ghettosled]

julio left insultech.

 

[MRKING]

I gots to ask

I gots to ask

Does it look like a manifold prototype will be in the works ?

 

[93ty475]

Re: I gots to ask

Re: I gots to ask

Does it look like a manifold prototype will be in the works ?

they made one, but it's kinda bulky..would be a super tight fit...not like the one pictured on the cat motor...

http://www.raceprovenmotors.com/insultech_dp.html

 

[MRKING]

a

a

I meant the exhaust manifold , kinda like the blanket wrap on the pic of the BIG motor .

But the dp cover looks like it would fit down to where the dp hooks under the cab . At least the top section anyway . How much to buy that prototype ?

 

[Jer]

So.. what page are these photos on because I'm not reading through all 14 pages of this. Give me photos and tell me price... that's all.

 

[dgoodhue]

Re: a

Re: a

I meant the exhaust manifold , kinda like the blanket wrap on the pic of the BIG motor .

But the dp cover looks like it would fit down to where the dp hooks under the cab . At least the top section anyway . How much to buy that prototype ?

The Downpipe come within ~inch of the passenger side exhaust manifold, so both of those would be difficult for fitting.

 

[viperman5]

Jer, photos can be seen in the GP. Cost is $125 plus $12 shipping.

http://www.syty.net/phpBB2/viewtopic.php?t=42535

 

[ghettosled]

something like this would be best for exhaust manifolds (b/c it is soo tight fitting), but i'm guessing it would be close to $1000 to do both sides.

 

[Jer]

Jer, photos can be seen in the GP. Cost is $125 plus $12 shipping.

http://www.syty.net/phpBB2/viewtopic.php?t=42535

D'oh! Never mind, I though they were turbo blankets for some reason. I'm not running the factory A2W set-up. Looks good though for $137 shipped. :rock:

 

[epix]

those IC Blankets do look good.. anyways I found this site about more thermal heat reflective produdcts and thought it fit in with this thread:

Universal Turbo Blanket:
http://www.designengineering.com/products.asp?m=sp&pid=31

Also manymore produdcts:
http://www.designengineering.com/products.asp

 

[epix]

those IC Blankets do look good.. anyways I found this site about more thermal heat reflective produdcts and thought it fit in with this thread:

Universal Turbo Blanket:
http://www.designengineering.com/products.asp?m=sp&pid=31

Also manymore produdcts:
http://www.designengineering.com/products.asp

 

[93ty475]

Re: Turbo Blankets: update SYTY PROTOTYPE PICS

Well, I went ahead and made my own turbo blanket...not the prettiest thing, but it's on there very tight and snug....used a turbo kit from thermotec ....cost around $100.00 for the kit and took the majority of last night to complete....should help with the burnt plug and starter wires...not to mention the underhood heat...there's a layer of the DP wrap material under the shiny foil type material....check it out....

 

[Ian Turgeon]

Re: Turbo Blankets: update SYTY PROTOTYPE PICS

Looks like it should help a lot, now the only thing left is the manifolds...


BTW your pcv system isnt going to work as designed with one of the valves missing (looks like you replaced it with a breather there). If so you might as well just replace the whole deal with a breather on that valve cover.

 

[93ty475]

Re: Turbo Blankets: update SYTY PROTOTYPE PICS

Looks like it should help a lot, now the only thing left is the manifolds...


BTW your pcv system isnt going to work as designed with one of the valves missing (looks like you replaced it with a breather there). If so you might as well just replace the whole deal with a breather on that valve cover.

I might just do the crossover and stop there....manifolds would be a definite pain....I'm still itching all over (two days later) from the fiberglass that got all over me :lol: ....

My plan was to run the other pcv hose (the one that goes where I stuck the breather) to my CAI....I'm not that sharp on pcv systems....I need to read up on that again....man, you don't miss a thing....I'm going to send you a few underhood photos if I ever finish so you could tell me what I missed ....did you notice the stock injectors? they're just in there to keep the dust out....my new ones are packaged in a box...