What did you do to your SyTy today? (part 2)

Gnocide

Gnocide

turbo game burt reynolds
Re: What did you do to your SyTy today? (part 2)

Aeroking said:
buttoned up alot of loose ends. i'm down to bolting the airbox on and plugging in the engine harness

041614-02_zps7aafed51.jpg


should be on the road by the weekend.
Click to expand...

thats fantastic

looks fantastic want to ride in it again!!
 
MotoCam360

MotoCam360

Member
The Dread Pirate Fisher

The Dread Pirate Fisher

Donating Member
Re: What did you do to your SyTy today? (part 2)

Took out my down pipe to clean up the shitty weld job that was done to weld the cat on, then decided to make my own mandrel bent 2 1/2" down pipe. The stocker has areas as small at 1.89" in the bends.

Next to install my wideband o2 bung and finish the rear section exhaust
 
H

HAMMERHEAD

Member
Re: What did you do to your SyTy today? (part 2)

Well I backed it out of the garage today and washed the winters dust off it and then spent about two hours debating whether to take it for a drive. Could not wait any longer. Took it to the sonoco and put $35 of 94 octane in it and went driving around for about an hour. Ran amazing except for the occasional stumble at idle. Put my foot in it a couple times and was pushing about 22psi and a/f was around 10.8 to 11. Pulled real hard. Now she is sitting back in the garage with the hood open and cooling down. Damn, I love these trucks when they are running good.
 
Aeroking

Aeroking

e.i.
Re: What did you do to your SyTy today? (part 2)

rough draft of an idea I had for a cold air box. I haven't decided if I like it or not. Radiator cap was an afterthought, lol. still gotta cut the hole for the turbo inlet. Maybe I'll put a lid on it.

042114-05_zpsbb6a8f5e.jpg


042114-03_zps5f62d2d3.jpg


042114-04_zpscc14c232.jpg


042114-01_zps849ddba1.jpg
 
Spnknu

Spnknu

Member
Re: What did you do to your SyTy today? (part 2)

Installed my wheels and deleted my wing. Started to clay bar and wax the truck. Tomorrow I'll throw on my new centercaps & fix my door pins. Enjoy



 
Baythan

Baythan

SY2TY2SY2TY
Re: What did you do to your SyTy today? (part 2)

^^ Wow...haven't seen a mismatch like that since the PPG truck! ^^

 
NOJIMMY

NOJIMMY

New member
Re: What did you do to your SyTy today? (part 2)

.....[You can pretty much guess what's gonna happen at this point after much restraint] :rotf:

IMG_3919_zpsf7d8e258.jpg
 
MotoCam360

MotoCam360

Member
Re: What did you do to your SyTy today? (part 2)

My new LS1 rear rotors came in yesterday...now I just need the calipers and backplates to start the job:

TYrearrotors_zps27b04309.jpg
 
B

blue83z

Donating Member
Re: What did you do to your SyTy today? (part 2)

Took my son out to a car show in the Syclone. He remembered from last year that you don't step on the cladding when you get in the truck. You make a "big kid step" right into the cab. Lol
 

Attachments

  • image.jpg
    image.jpg
    62.5 KB · Views: 0
You must log in or register to reply here.
Top