What did you do to your SY/TY today?

Status
Not open for further replies.
GAShan

GAShan

Donating Member
Re: What did you do to your SY/TY today?

Trouble shot Dan's Ty for a miss. Found this Taylor wire burned to a crisp. Looks like it wasn't seated all the way and was arcing to get to the plug. Plug had a carbon ring on it around the outside of the ceramic. But all the plugs looked good, nice color, consistant gaps and no oil. Also reattached a bunch of his claddding, many missing screws and bolts. Put it on the lift and did an oil change. The under engine cover was missing so dug out my last spare aluminum one and drilled and mounted it. Any more of them out there, or is anyone going to repop some?
 

Attachments

  • IMAG0076.jpg
    IMAG0076.jpg
    37.3 KB · Views: 0
qbnkiller

qbnkiller

Conflaguration Specialist
Re: What did you do to your SY/TY today?

396221920.jpg

396221921.jpg

396221762.jpg

396221759.jpg

396221761.jpg

396221758.jpg

396221763.jpg
 
B

blackty

Active member
Re: What did you do to your SY/TY today?

New gas tank, sending unit, Walbro and Racetronix kit. Almost done with the Renzfab e-brake cables. No gas in new tank yet. Just need to put back bumper on and hook hot lead to alternator. Oh, and get gas...Jim
 
Sean Krupa

Sean Krupa

Moderator
Re: What did you do to your SY/TY today?

Installed my Inner Fender plates. My dad surprised me for my birthday with these. He made them from 16ga Aluminum, Powder coated Satin black.

BEFORE:
CIMG1263.jpg

CIMG1264.jpg


AFTER:
CIMG1265.jpg

CIMG1266.jpg
 
Last edited:
Mtn Z

Mtn Z

Donating Member
Re: What did you do to your SY/TY today?

Finally swapped in a new distributor. The truck was parked for a month so I took it out and it ran like crap after being fine the last time I drove it. Checked the timing and it was all over the place. When I pulled the distributor, the magnet fell apart in little pieces. Couldn't believe it actually ran. Runs great now with no more tach flutter!
 
M

MySaudi

New member
Re: What did you do to your SY/TY today?

Took apart my gauge cluster to replace the lights and make it so i can actually see my speed while i'm driving..

208676_1996705354106_1137633639_2462728_4706627_n.jpg


207600_1996705034098_1137633639_2462726_1514298_n.jpg


205472_1996704794092_1137633639_2462725_4704283_n.jpg
 
montecoolkid

montecoolkid

New member
Re: What did you do to your SY/TY today?

wooo! i cut my fender off with a sawzall! haha, i'm stripping my smashed up typhoon, couldn't get to the back bolts and the front inner fender ones were spinning (fender was junk). i had to get it off to get access to the spark plugs. i took all the plugs out, took the master cylinder, abs modual, radiator and washer bottles, tail pipe, and battery box off. i also put battery ends on the cut cables and tried to get it to turn over with the key,(or where the would be if the column wasn't smashed). it doesn't turn over all the way, but now with the fender off i can see that the bell housing is smashed and the torque converter is right against the side, home fully its the tranny stopping it and not the motor! fingers crossed ill find out by the weekend when i cut the rest of the body off! i think ill cut it right behind the fire wall, and just have a dash left on the chassis. Soooo sad, but its for the greater good!
 
AutoVation

AutoVation

Member
Re: What did you do to your SY/TY today?

Quinnster said:
Thats really clean!:tup: What paint did ya use?
Click to expand...

GM Victory Red Touch Up Paint FTW
GM Black Touch Up Paint as well.

I put a lot on, let it dry overnight and then brushed the top surface to get the sharp transition from painted surface to the aluminum surface.
 
bezerk

bezerk

New member
Re: What did you do to your SY/TY today?

cleaned the surface on the deck and lower intake, so i can maybe put it back together tomorrow
 
92TYPHOON937

92TYPHOON937

Active member
Re: What did you do to your SY/TY today?

Stared at the white one for a minute and dreamed a lil bit bout havein a 6 liter in the 93 as I worked on the dodge withe the motor on the stand beside where I was workin lol
 
Fighting5thSVT

Fighting5thSVT

Active member
Re: What did you do to your SY/TY today?

Finished ABS delete and bled the brakes. I also started replacing valve seals. 2 down and 10 to go...Hopefully we will be running soon <fingers crossed>
 
BigBadSmoosh

BigBadSmoosh

Picking fights on I-65 since 2013
Re: What did you do to your SY/TY today?

finally, after a long time started putting things back onto my syclone

_MG_9444.jpg
 
Status
Not open for further replies.
Top