Search results

I will be glad to fax some information about pinion angles and how to measure them if anybody needs it. Eric

My lower IC radiator is toast and I need to know what everyone is using for a replacement. Is there a good aftermarket unit that will work without major modifications? I tried the search but couldn't find anything. Eric

A lot of you have been emailing me asking about bigger sway bars that I talked about being in the works a LONG time ago. First off, sorry it's taken so long to get these going. I have lots of excuses, all which don't matter, but here are some of them: Our controller was caught stealing 100's of...

As Product Manager for both Belltech and Suspension Techniques and holding both sets of rear sway bar instructions in my hand I can tell you the the rear sway bar is designed to be mounted UNDER the rear axle not on top of it. If anyone has a set of instructions with our logo on it that states...

Sorry for taking so long in responding to your help. The Ty would not start at all on Friday so I took the day off to work on it. I bypassed the Racetronix unit and plugged in to the factory wiring and it started right up. It runs and starts just fine. I know the fuse is good so now I will check...

Anybody out there? Maybe a bad ground? Eric

My Ty has been hard to start for the last week. It seems to not be getting FP everytime I turn the key on. Two days ago the fuse blew while I was passing a truck. I replaced the fuse and also replaced the relay that sends FP when you first turn the key on. Everything seemed normal for one day...

I will buy a dog tag. Eric

Last Friday I cruised from L.A. to Vegas in Ty #2350 following the #1 Marlboro Sy to the Primedia Vegas Nationals Truck show. I just wanted to give Lou a special thank you for bringing out the Marlboro truck and putting some miles on it. It drew a lot of attention at the show. That is one...

Thanks for the info! Eric

Can somebody please give me the extended and collapsed lengths on Sy/Ty factory shocks? Thanks, Eric

Merk, I sent you a private email. Hopefully we will have the new front bar 1-3/8 " and the rear bar (prototype being tested is 1-1/4") in production in the next couple of weeks. Sorry this is taking so long. Part of the problem is we are right in the middle of moving our R&D facilities into a...

Since they are next to the couch put a piece of round glass on top and you have some very cool end tables. They will be very cool on your truck. Eric :D

Make sure you use extruded aluminum blocks and not the cast aluminum type. The cast ones break easiser. Eric

Merk, Unless you are rubber man I would suggest adding about 6" of length to the fuel lines after you drop the tank. The hardest part of the job was trying to reconnect the lines. I installed the racetronix kit on my Ty and it is very simple, only took about 5 min. to install...

When installing leaf springs most people just unbolt the old ones and slap the new ones in without aligning the rear end or taking measurements. Your axle can pivot once the ubolts are loosened which would allow you to set the rear axle in proper alignment. (You could even throw out your pinion...

I just got off the phone with Amber from Truckin Magazine. She said that so far they have over 300 trucks registered to cruise from L.A. to Vegas for the Vegas National truck show. So far I know of 3 Sy/Tys that are going. Anyone else interested? See more info under West Coast Gatherings. Eric

Thanks Daron. The only way our springs would raise a truck is if the factory springs were toast and were sagging well beyond the drop of our springs. All of our springs are load tested at the manufacturing plant and at our machine shop to insure they are correct. Sure, you can pull a leaf out of...

Instructions have come a long way since the invention of digital. Most of them do have pics now. THIS ISN"T MEANT TO FLAME YOU but you do need to be smarter than the parts you are installing. You would be shocked to hear some of the tech calls we get here. People have even called with their...

All Belltech and ST bars come with everything you need to install your sway bar including grease that you will never get off your fingers. Here is an update on sway bars for Sy/Ty. Currently I have a prototype front bar on my Ty that is 1-3/8" diameter. We are also testing 1-1/2" bar for the...